i3 International i3F417U User Manual Download Page 11

10

 SPECIFICATIONS

The specifications are subjects to be change without notice

Camera

Signal system

NTSC

PAL

Scanning system

2:1 Interlace

Sync system

Internal

Scanning frequency (H)

15.734 KHz

15.625 KHz

Scanning Frequency (V)

 59.94 Hz

50 Hz

Day & Night (IICR)

Easy D/N ; Auto

Imaging area

4.9 mm x 3.7 mm

Image sensor

1/3” SONY CCD

Horizontal Resolution

560 TV lines

Effective pixels (HxV)

768 x 494

752 x 582

Lens

f=2.8~10mm,4X, F1.3 vari-focal lens

Min. illumination

0.02 lux

(F1.3, AGC on, 10 IRE)

0.35 lux

(F1.3, AGC on, 50 IRE)

AGC, BLC, Flickerless

ON/OFF

White balance

Auto: (2500°K~9500°K)

S/N ratio

> 50dB (AGC off)

View angle

Horizontal:76.92°(wide) ~ 22.73°(tele), Vertical:56.89°(wide) ~ 

17.07°(tele)

Video output

1Vpp composite output, 75 ohm

Gamma correction

0.45

Weight

1150g (2.54 lbs) approx.

Dimensions

150mm x 132mm (5.91” x 5.20”)

Vandal Resistant

1000kg (2,204.62lbs) impact resistance

Environment

Operating temperature

-10º ~ 50º C (14º~122º F)

Storage temperature

-20ºC ~ 60ºC (-4º ~ 140º F)

Humidity

30% ~ 90% RH

Electrical

Power requirement

12 VDC/24 VAC ±10%

Power consumption

4.5W (max.)

UTP

Yes - 300m (985 ft.)

Warranty

Product warranty

3 years

Summary of Contents for i3F417U













Reviews: