USER MANUAL
Page -2-
Am52RM Analog Dome Camera
in preparation for the mounting.
4.
Attach the supplied mounting template to the mounting
surface.
5.
Drill holes, as marked on the template and insert
supplied anchors into the holes. The number and
positioning of holes must match the ones pre-drilled on
the back box in Step 3.
6.
Drill the conduit hole for the camera cable, as
marked on the template, if using the top
conduit hole to route cables. Skip this step
if using the side conduit hole.
7.
Use the tapping screws provided
(if suitable for the installation) to
secure the camera’s back box to the
prepared mounting surface.
8.
Feed the camera cables through the
selected conduit hole. Use silicone
sealer around the chosen conduit hole
to maintain IP66 rating when installing
outdoors.
9.
Use the supplied security Torx key to attach the camera module to the back box. Use
three long machine-type screws pre-inserted into the camera module.
10.
Connect camera to DC12V or AC24V power
11.
Adjust the lens angle by panning and tilting the camera lens assembly and rotating the
camera lens base. Do not over-rotate the camera lens beyond the stop point to avoid
damage to the camera.
12.
If using service monitor to adjust the motorized
lens, attach the service monitor to the 2-pin
connector on the camera. Make sure the dipswitch
is set to CVBS to enable Service Monitor.
13.
Adjust the camera’s zoom and focus through
camera’s OSD, through IE or SRX-Pro.
See LENS
ADJUSTMENT section for more information.
14.
Use the joystick on the camera board to
adjust any additional camera settings (e.g.
image brightness, color or contrast, day/
night mode, etc.).
See CAMERA MENU
section for more information on camera’s
on-screen menu.
15.
Once the desired view is achieved, unplug
the service monitor and switch the dip
switch back into WDR mode (if using).
Replace camera’s inner liner (shroud) until it
snaps back into place.
16.
Replace the camera dome bubble and re-
tighten 3 silver screws securing the dome
bubble to the camera base.
Joystick
UP
3-axis Range Limitations:
Pan:
0 - 355°
Tilt:
0 - 75°
Rotation:
0 - 355°
CVBS / WDR
dipswitch
2-pin Service
Monitor
connector
FLUSH MOUNTING
Am52RM camera can be flush mounted with the use of i3’s flush mounting kit
(Part # AM42FM, sold separately). When flush-mounting the camera, do not use the
supplied camera back box.
Follow the mounting instructions supplied with the kit.
WALL MOUNTING w/ GOOSENECK BRACKET
Am52RM cameras can be wall-mounted with the use of i3’s gooseneck wall bracket
(Part # DB60, sold separately). Together with the optional DB60CPM bracket, DB60
gooseneck bracket has the capability of being corner- or pole-mounted.
Follow the mounting instructions supplied with the DB60 bracket.
Am52RM
Back Box
DB60
Gooseneck
Bracket
Use silicone
to maintain
IP66 rating
3/4” Rigid
Pipe
3/4” Electrical
EMT Conduit
Fitting
Use silicone
to maintain
IP66 rating
Am52RM
Back Box
Attach the top conduit hole of the camera’s back box
to the threaded end of the DB60 bracket and
rotate clockwise to attach the two together.
Use silicone sealer to maintain IP66 rating
when installing outdoors.
Complete installation as for Surface Mounting
from Step #8 onwards.
PENDANT POLE MOUNTING
Use a 3/4” Electrical EMT Conduit Fitting with a
rigid 3/4” pipe for this type of installation.
Attach the top conduit hole of the camera’s back
box to the threaded end of the 3/4” Electrical
EMT Conduit Fitting and rotate clockwise to
attach the two together.
Use silicone sealer to maintain IP66 rating when
installing outdoors.
Complete installation as for Surface Mounting
from Step #8 onwards.
CAMERA MENU
Use the camera’s on-board joystick to
adjust camera settings.
Use the button in the middle of the
Joystick to access the camera OSD MENU
and confirm selection. Move the Joystick
in UP/DOWN/LEFT/RIGHT directions to
navigate within camera menus.
UP
Press to access
camera menu
and to confirm
selection.
INSTALLING THE CAMERA
Prepare the mounting surface.
• Depending on the type of
installation, additional mounting
accessories may need to be
purchased.
• It is the installer’s responsibility
to ensure that the mounting
surface is suitable for the chosen
installation method.
• Based on installation location
and surface type, supplied screws
and anchors may not be adequate.
Mounting hardware is site-specific and
may need to be supplied by the installer.
SURFACE MOUNTING
1.
Use the supplied security Torx key to loosen three
screws securing the dome bubble housing to camera
module. Gently pull the dome bubble away from the
main camera module.
2.
Temporarily remove the camera liner/shroud for easier
lens adjustment.
3.
Depending on the type of installation and mounting
surface, complete drilling 2-4 holes in the back box
MENU > VIDEO OUT
Under VIDEO OUT, set the camera video standard to NTSC or PAL.
MENU > LANGUAGE
Under LANGUAGE, select one of the available options, including English, French, etc.
MENU > SETUP
Under the SETUP Menu, use the camera’s built-in Joystick to move around the menu
tree and to select setting categories.
