background image

Page 

5

 of 

20

 

Moving Head Controller 2.0 Manual Rev2 

2.

 

I

NTRODUCTION

 

Features 

· DMX Output 
· DMX Input 
· USB Input 
· JOYSTICK  
· Controls up to 6 different types of lights with up to 

24 DMX

 channels each 

· Controls multiple lights simultaneously 
· Passes through up to 

512

 DMX channels from input to output 

· Stores and plays back 

128 chases

  

· Stores and plays back 9 independent Chases of up to 128 Steps in total 
· Accepts fader customizations 
· Accepts 

25 customizable light libraries

 

· Plays back multiple chases in sequential order 
· Plays back multiple Chases simultaneously  

· Controls lights “on the fly” in Playback mode

 

· Triggers chases and scenes with preset transition and standby times 
· Accepts USB input to trigger scenes and chases 
· Accepts USB input to store, edit and upload parameters and functions     through 
the provided GUI interface 
· Accepts new firmware versions and is user upgradable 

 

Product 

The moving Head Controller 2.0 (the board) is a small, powerful controller with a 
built-in Joystick that enables it to simultaneously control multiple moving heads to 
be used in Follow-Spotting applications. 

 

Description 

It has several playback modes and can control up to 512 DMX channels which are 
accessed using the <LIGHTS> buttons. Each one of the 6 <LIGHTS > button is linked to 
up-to 24 predetermined DMX channels. These 24 channels are broken down into 
different groups allowing 13 of the 14 physical faders alongside internal functions to 
control up to the 24 channels. 

 

Mounting 

The moving Head Controller 2.0 comes with 2 accessories Mounting Ears for rack 
mounting into a standard 19-inch rack. It also has rubber feet so it can sit on a table 
top. 
 

Mounting 

Accessories 

 

 

 

Summary of Contents for Moving Head Controller 2.0





















Reviews: