①
Pass the cables from the wall to the WV-QWL501-W.
Adjust the length of the cables so that the cables
of approx. 300 mm {11-13/16 inches} come out
from the opening of the WV-QWL501-W.
Note:
• Do not bundle the cables (Ethernet cable,
power cable, etc.) during installation.
Mounting of inner cover (accessory) may
become difficult. (The provided illustration
shows the Ethernet cable as a
representative image.)
②
Fix the WV-QWL501-W on a wall with fixing
screws (4 pcs.) (M10: locally procured).
Minimum pull-out strength: 823 N {185 lbf}/
per 1 pc.
If the product is installed outdoors, the waterproofing
treatment is necessary. Refer to the operating
instructions of used mounting bracket for further
information on how to fix.
③
Attach the cover part of this product to the
WV-QWL501-W, and then fix it with M6 hexagon
screws (4 pcs.) (provided with WV-QWL501-W).
(A hexagon wrench with a width of 5 mm is
required.)
(Recommended tightening torque: 2.45 N·m
{1.81 lbf·ft})
* Fix the cover so that the name plate of this
product comes in front of the WV-QWL501-W.
④
After fixing this product on the WV-QWL501-W, lay the cables as shown in the upper right
illustration and confirm that the ends of the cables reach the cable line inside the cover of this
product.
①
②
③
④
Cable line
Cables
Name plate
Cover part of
WV-QSR501-W
Cover part of
WV-QSR501-W
Approx. 300 mm
{11-13/16 inches} from the
opening of WV-QWL501-W
Name plate
WV-QWL501-W
M6 hexagon screw (4 pcs.)
M10 screw (4 pcs.)
[2] Fix the cable with the inner cover
①
Wire the cables as shown below.
②
Fix inner cover (accessory) using Screw A (3 pcs.)
(M3 × 8mm {5/16 inches}: accessory).
(Recommended tightening torque: 0.78 N·m
{0.58 lbf·ft})
Inner cover
(accessory)
Screw A (3 pcs.) (M3: accessory)
Be sure to read “Precautions” and “Precautions for installation” before installation.
Refer to the operating instructions of the camera for details on the camera installation
(including the camera mounting, cable connection and adjustment).
[1] Fix the wall mount bracket (WV-QWL501-W) on a wall and
attach the cover of the mount bracket (WV-QSR501-W) to the
WV-QWL501-W
①
Pass the cables from this product through the
attachment plate (camera accessory).
②
Secure the attachment plate to the cover of this
product with Screw C (4 pcs) (M4×8 mm
{5/16 inches}: accessory).
(Recommended tightening torque:
0.78 N·m {0.58 lbf·ft})
* The illustration on the right is an example of fixing an
attachment plate that has 4 holes for fixing the
camera.
③
Connect the cables to the camera. The cable
connector is waterproofed. For details about this
treatment, refer to the operating instructions of the
camera you are using.
④
Align the OPEN mark on the side of the camera
enclosure with the claw of the attachment plate,
insert the attachment mounting screws (2 or 3 places)
on the bottom of the camera into the holes of the
attachment plate, and rotate it about 15° to
temporarily fix it.
→
Refer to the operating instructions of the camera for
the parts to remove the enclosure, fix the camera,
adjust the angle of view, and install the enclosure.
→
Refer to the operating instructions of the camera for
details on the following preparations and details on
how to mount the camera.
⑤
Remove the enclosure, cushion wrap, and protective
sheet from the camera body before attaching the
camera to this product.
⑥
As required, remove the power cord plug (camera
accessory) and EXT I/O terminal plug (camera
accessory) that are attached to the camera body and
install the SD memory card.
⑦
Connect the cables to the camera.
⑧
Align the OPEN mark on the side of the camera with
the claws of the attachment plate, insert the
attachment mounting screws (2 places) on the bottom
of the camera into the holes of the attachment plate,
and rotate it about 15° to temporarily fix it.
→
Therein after, refer to the operating instructions of the
camera to fix the camera, adjust the angle of view, and
for the parts to fit the enclosure.
[3] Attach the bracket to the cover part of this product, and fix the
camera
* The enclosure part is omitted from the illustration on the upper right.
Screw C (4 pcs.)
Attachment plate
(camera accessory)
Screw C (2 pcs.)
Outdoor dome type camera
Screw C (4 pcs.)
Attachment plate
(camera accessory)
This product
Base guide plate
(accessory)
Indoor dome type camera
using an attachment plate
Indoor dome type camera
attached directly to the
installation surface
Cover part of this product
Attachment plate hole
This product
Screw B (4 pcs.)
Screw B (4 pcs.)
Base guide plate
(accessory)
This product
When installing an outdoor dome type camera
①
Pass the cable through the base guide plate (accessory).
②
Fix the base guide plate to the cover part of this product
by using Screw B (4 pcs) (M4×8 mm {5/16 inches}:
accessory).
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
③
Pass the cable through the attachment plate
(camera accessory).
④
Fix the attachment bracket to the base guide bracket by
using Screw C (4 pcs) (M4×8 mm {5/16 inches}:
accessory).
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
①
Pass the cable through the base guide plate (accessory).
②
Fix the base guide plate to the cover of this product by
using Screw B (4 pcs.) (M4×8 mm {5/16 inches}:
accessory).
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
③
Connect the cables to the camera.
④
Fix the camera to the base guide plate using 2 of Screw
C (M4×8mm {5/16 inches}: accessory).
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
→
Therein after, refer to the operating instructions of the
camera to adjust the angle of view, and for the parts to fit
the enclosure.
* The enclosure part is omitted from the illustration on the
lower right.
When installing an indoor dome type camera
(When installing an indoor type camera, install the combined brackets indoors.)
When installing an indoor dome type camera without an attachment plate
(When installing an indoor type camera, install the combined bracket indoors.)
Installation
