30
31
4-1-1 WI-FI Connection
Click the shortcut on the main screen, select “Internet Connection Manager”, click “WI-FI setting”,
then enter the WI-FI setting screen, now select “WI-FI” and activate it.
Notes:
1. First close the WI-FI network, only one network can be used, otherwise there will be errors.
2. This device will automatically detect the USB Ethernet card and switch on the “Ethernet”. There
will now be a network icon in the status column.
3. Wait a moment, as this device will try to connect to Internet automatically. If the router and the
DHCP service are already open, and the netgate, DNS and relevant settings have been applied,
then the device will connect to the Internet automatically. (The Ethernet card function must be
selected already).
4. If the device fails to connect, usually this is because the settings in the router are not correct.
You can set the parameters in the device as follows:
a. Enter setting/Ethernet setting, select and open Ethernet.
Enter configuration information, choose “static IP setting”, then enter the static IP setting
screen (the default setting is automatic aquiring IP. Usually, automatic aquiring IP is fine for
everything, but some companies‘ routers will use specified IPs, not allowing automatic aquiring
IP, it depends on router settings, therefore static IP needs to be used at this time).
b. There is no need to fill in the Ethernet card device and physical address. The machine will auto
-
matically detect this, after successfully connecting the Ethernet.
In the IP address column, enter the IP address, the default usually being 192.168.1.1xx.
c. In “subnet mask”, enter network segment mask, the default is 255.255.255.0.
d. In the “DNS server”, enter your local network service provider‘s DNS server IP. A different
location has a different DNS server IP - if you are unsure, you can search by Google.
e. Enter the gateway in the „default gateway”. The general default is 192.168.1.1 (you can check
the router‘s manual for confirmation). It must be set to the same as the router; otherwise
connection will be shown, however cannot connect to the Ethernet.
f. Finally, click the lower right corner of the “Save” button, then select Save. The system will
automatically connect after saving, then you can use the Ethernet.
5. Close the Ethernet, unplug the “Ethernet” cable, now you can turn off the Ethernet connection.
6. Unplug the OTG cable.
Attention:
1. If you are unsure about router settings and the DHCP service, please consult the router‘s manu-
facturer, point-of-service, network service providers (or ask network management, network
experts, etc.), or research independently. Our company does not supply this kind of service and
support.
2. If you are not using Ethernet, please unplug the OTG cable and Ethernet card, otherwise the
machine will continue to use power.
4-3 Webpage Browser
Set up the network as in chapter 4-1, you can then use the browser to browse the web. Click the
shortcut on the main screen. Enter the required URL in the address bar. Open the web page; then
slide your finger up and down the screen to view other parts of the page.
After WI-FI has opened, it will automatically search for wireless network, this shows on the menu,
now click wireless network, enter the password screen, and now input the password and connect.
Seconds later, the system will connect to wireless network automatically.
!
When WI-FI is open, this will make the machine use 25 % more power. When not using
WI-FI, please turn it off to extend the battery life.
4-2 Ethernet Setting
Using the Ethernet card (USB-RJ45) when connecting to the Internet.
There are two requirements needed to use USB-RJ45 to connect to the Internet, and these are
detailed below:
1. ADSL account and password are set up correctly on router.
2. USB-RJ45 network card is the model which is supported by this device.
Models supported are listed below:
AX88772/AX88772a/AX88772B/AX88178/AX88760/QF9700/SR9600/MCS7830/MCS7832/MCS7730
Steps for Internet Connection:
First connect the network cable to the USB Ethernet card, then insert the USB OTG cable which is
meant for this device into USB Ethernet card and the other end into USB port of the device.
