HZ Security HZ-WT-ADV-24 User Manual Download

Page: 21 / 30

Model Number

-WT-ADV-24 User Guide

Page | 20

2021

Hangzhou Weiqi Electronic Co., Ltd.

ENSITIVITY

DJUSTMENT

ENSITIVITY IS ADJUSTABLE TO

1000

LEVELS

[0~999].

ELECT

ENSITIVITY AND PRESS

NTER

Zone and Grade

ARE THE TWO

ENSITIVITY MODE

CHOICES

The Grade screen

IS USED TO SET THE OVERALL

SYSTEM SENSITIVITY

SE THE LEFT AND RIGHT

BUTTONS TO SELECT

IGH OR

OW SENSITIVITY

RESS THE

NTER BUTTON TO SAVE THE SETTINGS

AND RETURN TO THE PREVIOUS MENU

The Zone screen

IGURE

SHOWS THE

DEFAULT FOR A

ZONE CONFIGURATION AFTER SELF

CALIBRATION

SE THE UP AND DOWN BUTTONS TO

HIGHLIGHT A SPECIFIC DETECTION ZONE AND PRESS
ENTER TO MODIFY THE SENSITIVITY OF THAT ZONE

O MANUALLY ADJUST THE PARAMETERS

PRESS THE

BUTTONS TO SELECT SPECIFIC DIGITS

THEN THE USE UP AND DOWN BUTTONS TO ADJUST
THE VALUE FROM

–

ETECTION ZONE

SENSITIVITY IS ADJUSTABLE BETWEEN

999.

RESS THE

NTER BUTTON TO SAVE THE SETTINGS

AND MOVE TO THE NEXT ZONE

RESS THE POWER

BUTTON TO RETURN THE PREVIOUS MENU

Figure 18

Figure 21

Figure 20

Figure 19

Summary of Contents for HZ-WT-ADV-24





























Search results

Summary of Contents for HZ-WT-ADV-24

Reviews:

Related manuals for HZ-WT-ADV-24

Brands by name

Popular brands

HZ Security HZ-WT-ADV-24, User Manual

Search results

Summary of Contents for HZ-WT-ADV-24

Reviews:

Related manuals for HZ-WT-ADV-24

Brands by name

Popular brands