background image

4.4.4 Hedge Trimmer operation instructions

4.4.4.1 

U

se the unit only after you have read the instruction manual carefully.

 

4.4.4.2 O

b

serve all the safety instructions contained in the manual.

4.4.4.

3

 Hedge trimmers may 

b

e used not only on hedges

 b

ut also to cut  

shru

b

s.

4.4.4.4 Always attach the e

x

tension.    

5. INSPECTION & MAINTENANCE

Always switch the power unit off when doing maintenance or a repair. 
The following instructions shall apply to regular conditions of use. In 
severe conditions and longer periods of work, it is necessary to shorten the 
intervals as appropriate. 

5.1

 

After finishing work, check over the entire machine for damage and any loose parts and 

clean machine. 
5.2

 

Regular checks and treatment: 

5.2.1

 

Check the ignition plug and replace if necessary. 

5.2.2

 

Check the function and quantity of the plastic cord on the reel, replenish as 

required. 

5.3

 

Inspection and maintenance safety instructions. 

5.3.1

 

Only a unit maintained and cared for on a regular basis may be considered as a 

safe to use machine. Insufficient maintenance and care may result in emergencies 
and unforeseen accidents. 
5.3.2

 

Only authorised servicing agents may do repairs requiring special professional 

knowledge. 
5.3.3

 

Follow these precautions: 

5.3.3.1

 

Keep all nuts, bolts and screws tight to be sure the equipment works 

as intended. 
5.3.3.2

 

DO NOT 

store with petrol in the tank.

5.3.3.3

 

Always allow engine to cool before storing. 

5.3.3.4

 

Always keep hot engine parts away from grass, leaves and excess 

grease. 
5.3.3.5

 

Always replace worn or damaged parts. 

5.3.3.6

 

If petrol tank needs draining, always do it outdoors. 

5.3.3.7

 

DO NOT 

attempt to repair the machine unless you are competent to

do so. 
5.3.3.8

 

Use only genuine Hyundai parts and accessories. 

Page 14

Ver 2

Summary of Contents for HYMT33

























Reviews: