background image

2.

10

.6.

 

NEVER attempt to unclog either the feed hopper or discharge chute while the

engine is running. Immediately shut off the engine. Allow the cutting disk to 
come to a complete stop. Remove the clogged material. Inspect for damage 
and check for any loose parts for repair or replacement. 

2.

10

.7.

 

Whenever you leave the operating position or if you have to remove

processed material, leaves or debris from the machine, ALWAYS shut down the 
engine, disconnect spark plug wires, keeping them away from the spark plugs 
to prevent accidental starting, and wait for all moving parts to come to a 
complete stop. 

2.

10

.8.

 

DO NOT tilt the machine while the engine is running.

2.

10

.9.

 

ALWAYS stop the engine before moving the machine.

2.

10

.10.

 

ALWAYS make sure that the engine is switched off and that the cutting

disk

 

and engine are at a complete standstill and the belt drive is disengaged 

before opening the cutting disk housing. 

2.

10

.11.

 

Keep combustible substances away from the engine when it is hot.

2.

10

.12.

 

NEVER cover the machine while the muffler is still hot.

2.

10

.13.

 

Feed only clean materials into the machine. Foreign matter like soil, sand,

grit, stones, pieces of metal, etc. will damage the sharp edge of the cutting 
knives. Root balls and dead wood will also blunt the blades quickly. Avoid 
feeding any flax and cabbage tree leaves into the machine as these stringy 
materials can wrap around the rotor shaft and work their way into the bearing. 

2.

10

.14.

 

Avoid feeding short, stubby pieces of wood into the machine, as they tend to

bounce and spin in the feed hopper. Feed these short pieces together with 
longer pieces. After becoming familiar with the machine, prune to suit its 
capabilities. 

2.

10

.15.

 

DO NOT force the branches into this machine. Allow the machine to

automatically feed through. 

2.

10

.16.

 

NEVER operate the machine on slopes.

2.

10

.17.

 

DO NOT alter or adjust any part of the wood chipper or its engine that is

sealed by the manufacturer or distributor. Only a qualified service 
technician may adjust parts that may increase or decrease governed engine 
speed. 

2.

10

.18.

 

This wood chipper is for off-road use only. NEVER attempt to tow the

machine on public highways, roads, or thoroughfares. 

2.

10

.19.

 

NEVER operate this machine without feed hopper or discharge chute

properly attached to the machine. 

2.

10

.20.

 

Move the machine at least 3m away from the refueling point before

starting engine. 

2.

10

.21.

 

ALWAYS check the oil level of the engine before use.

2.

10

.22.

 

Inspect that all nuts and bolts are tight and well connected to ensure the

safety and reliability of this machine prior to any operation. 

2.

10

.23.

 

Inspect the air pressure in the tires prior to use and pay attention to sharp

objects when moving the machine to prevent the tires from being pierced. 

2.

10

.24.

 

Since some parts of the machine are made of plastic or rubber materials, it

should be kept away from any chemical article to prevent a chemical reaction 
from occurring. 

Page 10

Summary of Contents for HYCH7070

































Reviews: