background image

1.50 

Batteries (where present). 

1.51 

Batteries present a risk if they become damaged by the possible leaking of 
electrolyte. This electrolyte is an acid and can cause serious burn injuries. Care 
should be taken when working on or near them. 

NOTE 

the electrolyte may be in 

a liquid or gel form. 

1.52 

Should you come in to contact with electrolyte you should; 

1.53 

Remove all clothing contaminated with electrolyte. If you cannot remove then 
saturate them in water. 

1.54 

Get medical assistance as soon as possible. You must advise the medical staff of 
the type of acid. 

1.55 

Lead/acid battery = dilute sulphuric acid. 

1.56 

Nickel/cadmium  = potassium hydroxide alkali electrolyte. 

1.57 

Use fresh running water to wash off excess electrolyte, continue this until medical 
assistance arrives. Make sure that you do not was the electrolyte to another part of 
your body or face. 

1.58 

If electrolyte comes in to contact with Eyes the electrolyte needs to be immediately 
washed away with large amounts of water. Make sure that you do not wash the 
electrolyte to another part of your face or body. 

1.59 

Gasses from charging batteries are highly flammable and great care should be taken 
to charge in well ventilated areas. 

1.59.1 

There is an explosion risk if the battery terminals are short circuited, when 
connecting/disconnecting 

ALWAYS 

exercise great care so that the terminals or 

battery leads are 

NOT 

allowed to touch and cause a spark. 

ALWAYS 

use suitable 

insulated tools. 

1.60 

Vibrations (where applicable). 

1.61 

Prolonged use of hand held (operated) machines will cause the user to feel the 
effects of/from vibratio

ns. These vibrations can lead to white finger (Raynaud’s 

phenomenon) or carpal tunnel syndrome. This condition reduces the ability of the 
hand to feel and regulate temperature, causing numbness and heat sensations and 
may cause never damage and circulatory tissue death. 

1.62 

Not all factors that lead to white finger disease are known, but cold weather, smoking 
and other diseases that affect blood vessels and blood circulation as well as large 
and long-lasting impact of shocks are considered factors in the formation of white 
finger. Note the following to reduce the risk of white finger and carpal tunnel 
syndrome; 

1.63 

Wear gloves and keep your hands warm. 

1.64 

Take regular breaks. 

1.65 

All of the above precautions may help reduce the risk of white finger disease but not 
rule out the carpal tunnel syndrome. Long-term and regular users are therefore 
recommended to observe the condition of your hands and fingers. Seek medical 
attention immediately if any of the above symptoms should occur. 

Summary of Contents for HYC6200X

































Reviews: