background image

1. SAFETY

1.1 

General Safety Notes. 

1.2 

The operator of the machine is responsible for, and has a duty of care in making sure 
that the machine is operated safely and in accordance with the instructions in this 
user manual. Keep the manual safe and pass it on if the machine is loaned or sold to 
another user.

 

1.3 

Please note the following safety points. 

1.4 

The machine should never be left it in a condition which would allow an untrained or 
unauthorised person/s to operate this machine.

 

1.5 

All due care and diligence should be taken by the operator for the safety of and with 
regard to those around whilst using the machine. 

1.6 

Some or all of the following - warning signs, symbols and/or PPE pictograms may 
appear throughout this manual. You 

MUST 

adhere to their warnings. Failure to do 

so may result in personal injury to yourself or those around you.

 

 

DANGER

 

Indicates a hazard, which, if not avoided, could result in serious injury or death.

 

 

WARNING

 

Indicates a hazard, which, if not avoided, could result in serious injury.

 

 

CAUTION

 

Indicates a hazard which, if not avoided, might result in minor or moderate injury.

 

 

NOTE

 

Indicates a situation that could easily result in equipment damage.

 

READ and keep the manual safe and pass it on if the machine is loaned or sold to another user.

 

You MUST fully understand all instructions to ensure you use and operate the machine safely.

 

Appropriate Personal Protective Equipment (PPE), 

MUST 

be worn at all times when operating or 

repairing the machine. 

Summary of Contents for HYC6200X

































Reviews: