background image

1.70 

Noise (where applicable). 

1.71 

The operating noise of the machine can damage your hearing. Wear hearing 
protection such as earplugs or ear defenders to protect your hearing. Long-term 
and regular users are advised to have hearing checked regularly. Be especially 
vigilant and cautious when hearing ear protection because your ability to hear alarm 
warnings will be reduced. 

1.72 

Noise emissions for this equipment is unavoidable. Carry out noisy work at approved 
times and for certain periods. Limit the working time to a minimum. For your personal 
protection and protection of people working nearby it is also advisable for them to 
wear hearing protection. 

1.73 

See CERTIFICATE of CONFORMITY section for Outdoor Noise declaration of 
conformity. 

MACHINE SPECIFIC SAFETY 

1.80 

General Machine Safety. 

1.81 

Read the owner’s manual carefully to understand how to operate this machine 
properly. 

1.82 

The water pump will need priming with water BEFORE use. 

1.83 

Check the water pump over before use, if any problems are found you MUST make 
sure they are dealt with by the appropriate person before use. 

1.84 

Check around and underneath the water pump for signs of oil or fuel leaks. 

1.85 

Remove any dirt or debris, especially from the engine exhaust and recoil starter. 

1.86 

Look for any signs of damage. 

1.87 

Check that all nuts, bolts, screws, hose connectors and clamps are tightened. 

1.88 

Check the general condition of the hoses. 

1.89 

Before connecting the hoses to the water pump, make sure that they are in good 
condition. 

1.90 

Remember that the suction hose must be of a reinforced construction to prevent the 
hose from collapsing. 

1.91 

Check that the sealing washer in the suction hose is in good condition. If there are 
any leaks or a poor connection, the pump will draw in air and notfunction. 

1.92 

Check that the hose connectors and clamps are securely installed. 

1.93 

Check that the strainer is in good condition and is secured on the suction hose. 

WARNING

 

Operating the water pump with a low oil level will damage the pump.

 

NOTE 

Before checking the oil, place the water pump on a flat, level surface. 

Summary of Contents for HY25-4





























Reviews: