Hyundai HY25-4 User Manual Download Page 20

20 

8. TROUBLE SHOOTING

 

WARNING 

Before cleaning, inspecting or repairing your unit, you MUST make sure that the 
engine has stopped and allowed to cool. 
You MUST disconnect the spark plug lead to prevent any accidental starting. 

6.0 

Engine 

Engine will not start

Cause

Corrective measure

Check controls 

Fuel valve OFF 

Move fuel lever to ON position 

Choke OPEN 

Move the choke lever to the 
CLOSED position unless the 
engine is warm 

Engine switch OFF

Turn the engine switch ON

Check fuel 

Out of fuel 

Refuel 

Bad fuel, pump has been 
stored without treating or 
draining fuel or refuelling with 
bad fuel 

Drain the fuel tank and 
carburetor and refuel with 
fresh fuel 

Remove and inspect the spark 
plug 

Faulty spark plug or 
improperly gapped 

Replace with new spark plug 
or adjust the spark plug gap 

Spark plug wet with fuel, 
flooded engine 

Dry the spark plug and 
reinstall. Start engine with 
throttle lever in FAST 

Contact dealer 

Fuel filter clogged, carburetor 
malfunction, ignition 
malfunction, valves stuck etc. 

Return to dealer for repair 

6.1 

Water Pump 

No output from pump 

Cause 

Corrective measure 

Check pump chamber

Pump not primed

Prime pump

Check suction hose 

Hose collapsed, cut or 
punctured 

Replace hose 

Strainer not completely 
underwater 

Sink strainer and end of 
suction hose completely 
underwater 

Air leak at connector 

Replace sealing washer if 
damaged or missing. Tighten 
hose connector and clamp 

Strainer clogged 

Clear debris from strainer 

Measure suction and 
discharge head 

Excessive head 

Relocate pump and hose to 
reduce head 

Check engine 

Engine lacks power 

See engine trouble shooting 
above 

Summary of Contents for HY25-4





























Reviews: