ENG - 18
–
Do not place the appliance under electrical socket.
For safety reasons, leave
the minimum distance of 0,5 m between the appliance and any obstacle on any side (furniture,
walls, etc.).
–
Do not use the appliance in bathrooms in zones 0, 1 and 2! It must not be used in a close
proximity of bathtub, shower or swimming pool.
– The appliance must not be immersed in water or other liquids (not even partially)! If the
appliance falls in water, do not take it from the water! First disconnect the power cord plug from
the electrical socket, and then take out the appliance from the water. In such cases, bring the
appliance to a specialised service centre to verify its safety and proper operability.
–
The appliance must not be immersed in water or other liquids (not even partially)! If the
appliance falls in water, do not take it from the water! First disconnect the power cord plug from
the electrical socket, and then take out the appliance from the water. In such cases, bring the
appliance to a specialised service centre to verify its safety and proper operability.
–
ATTENTION
: Do not use this heater in series with an external timer, remote controller or any
other device that switches on the appliance automatically, since a fire risk exists when the
heater is accidentally covered or displaced at the moment it switches on.
– Do not handle the appliance with wet hands
–
Do not plug the power cord in the electrical socket and do not unplug it with wet hands
or by pulling the power cord!
–
The appliance must not be used in a damp or wet environment and in any environment with the
danger of fire or explosion (
premises where chemicals, fuels, oils, gases, paints and other
flammable or volatile materials are stored
).
–
Only use the appliance in the working position at places with no risk of overturning and in
a sufficient distance from other objects (such as
curtains, drapes
, etc.), heat sources
(e.g.
fireplace, heater, stove, cooker, radiators, hot air ovens, grills
) and wet surfaces
(e. g.
sinks, wash basins
).
–
Make sure that no impurities get inside the appliance (e.g.
dust clouds, hairs
etc.). If impurities
are sucked and settle inside the appliance, clean it.
–
Do not put the switched on fan on soft surfaces (e.g. on a
bed, towels, wipers, carpets
).
–
Do not switch on the fan if the appliance is not completely assembled or if the blade wheel
covers are damaged.
–
This appliance is not intended for outdoor use.
–
The appliance is equipped with a thermal cut-out that will interrupt power supply (to the fan
heating spirals), if the appliance dangerously overheats. If overheating occurs, switch off the
appliance, disconnect it from the power supply, remove any obstacles preventing the air flow,
and let the appliance cool down for about 10 minutes. If the cut-out occurred for reasons other
than air flow reduction (e.g. motor bearing is seized), have the appliance repaired by
a specialised service centre.
– Do not modify the appliance surface in any manner (e.g. by
self-adhesive wallpapers, foils
,
etc.)!
– When handling the appliance, avoid causing any injury (e.g.
burns
).
–
Before every connection or disconnection of the appliance from power supply make sure that
switch
P4
is in
0
position.
– Do not place any device with open flame in the air flow coming out from the appliance because
of danger of burning process interruption.
– Never expose yourself (or animals) to the air flow for an extended period of time.
It may cause health problems.
– Only use original components designed for this type.
–
Never put fingers or other objects into inlet and outlet holes of the fan.
–
Check the condition of the power cord of the appliance regularly.
– Never put the power cord on hot surfaces and never let it hang over table edge or worktop
edge. If the cord is caught or pulled, e.g. by children, the appliance may overturn and fall down,
causing a serious injury!
