Hytronik HED1050L, Instruction Manual

Page: 3 / 4

2IIĺRQWKHOLJKWWXUQVRQDQGJRHVWRVHQVRUPRGHQRPDWWHULIDPELHQW/X[OHYHOH[FHHGVWKHGD\OLJKWWKUHVKROGRUQRW
Note: when manually push on the master via push switch, it can send a “on” signal to all slaves in the same group. The slaves will turn on when
ambient light is below its daylight threshold preset.
* Long push (>1s): dim up/down the hold-time brightness between 10% and 100%.
Note: if end-user do not want this manual override function, just leave the “push” terminal alone and don’t connect it to any wire.
SECTION 3 REMOTE CONTROL
1. Press button “start” to program.
2. Select the buttons in “Detection range”, / “Daylight hreshold”, “Hold time”,
“Stand-by time”, “Stand-by dimming level” to set all parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s). For example, to pre-set
GHWHFWLRQUDQJHGD\OLJKWWKUHVKROG'LVDEOHKROGWLPHPLQVWDQGE\WLPH’
stand-by dimming level 30%, the steps should be as follows: Press button Start,
EXWWRQ'LVDEOH6KLIWPLQ6KLIW’0HPRU\%\SRLQWLQJ
to the sensor unit(s) and pressing Apply, all settings are passed on the sensor(s).
Scene prog. [ zone ] (One-key-commissioning)
7
RESET [ button ]
Press button , all settings go back to the default settings.
Detection range:100% Hold-time:1min Stand-by Period:5min
Stand-by dimming level:20% Daylight sensor:lux disable
Shift [ button ]
3UHVVEXWWRQWKH/('RQWKHWRSOHIWFRUQHUZLOOÀDVKWRLQGLFDWHPRGHVHOHFWLRQ
All values / settings in RED are valid for 20 seconds.
Auto Mode [ button ]
Press button to initiate automatic mode. The sensor starts working and all settings remain
as before the light was switched ON/OFF.
Brig/- [ button ]
Press button to adjust the light brightness between 10%~100%.
6
6
7
Power output [ button ]
Press button , the light output shifts between 80% and 100%.
Note: the function of “Sensor off” and “Twilight” are disabled.
Permanent ON/OFF [ button ]
Press button ,to select permanent ON or permanent OFF mode.
* Press button / to resume automatic operation.
The mode will change to AUTO Mode after power failure.
1
1
2 4
2
Detection range [ zone ]
Press buttons in zone to set detection range at 100% / 75%/ 50% / 10%.
Daylight threshold [ zone ]
Press buttons in zone to set the daylight sensor at 2Lux / 50Lux / 100Lux / 300Lux
/ 500Lux or Disable.
1RWH7RVHWGD\OLJKWVHQVRUDW/X[/X[/X[SUHVVEXWWRQ6KLIWDW¿UVW
3
3
4
4
5
5
8
9
10 11
12 13
7
8 3 3 7 10
11
12 13
8
8
9
9
3
Ambient daylight threshold [ button ]
1. Press button Shift, the red LED is on for indication.
2. Press button ,the ambient lux level is sampled and set as the new daylight threshold.
Press buttons in zone to set the hold time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
1RWH7RVHWKROGWLPHDWVPLQPLQPLQSUHVVEXWWRQ6KLIWDW¿UVW
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button or anybutton in zone .
Hold time [ zone ]
10
10
3
11
11
11
3
2
Stand-by time [ zone ]
3UHVVEXWWRQVLQ]RQHWRVHWWKHVWDQGE\SHULRGDWVVPLQPLQPLQPLQK’
1RWH³V´PHDQVRQRIIFRQWURO³’´PHDQVELOHYHOFRQWURORQZKHQPRWLRQLVGHWHFWHGDQGUHPDLQVDWWKHVWDQGE\GLPPLQJOHYHOZKHQQR
presence is detected after hold-time.
Stand-by dimming level [ zone ]
Press buttons in zone to set the stand-by dimming level at 10% /20% / 30% / 50%.
Note:the function of 24h/ 12h/ 4h/ 30s are disabled.
12
12
13
13
Semi-auto Mode
[ button & ]
1. Press button Shift (the red LED is on for indication),
2. press button to initiate semi-auto mode. The fixture is manually on by push-switch and
automatically off in semi-auto mode.
3
3
4
4
2
& A
I I I
Note: the buzzer beeps one time when RC
receives signal successfully
HRC-11
6
8
10
11
13
14
12
2
4
1
3
7
9
5