HC403VRC-KD-20170329-A1
Hytronik Industrial Ltd. | www.hytronik.com
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bo'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel: 86-752-2772020 Fax: 86-752-2777877
3. Section Remote Control
Detection area:
Detection range can be tuned by selecting the combination on the DIP switches to fit precisely
for each specific application.
3. Section Settings
Detection area:
Detection range can be tuned by selecting the combination on the DIP switches to fit precisely
for each specific application.
I – 100%
II – 75%
III – 50%
IV – 10%
50%
75%
100%
10%
2
1
I
II
III
IV
I – 5S
II – 30S
III – 1min
IV – 5min
V – 10min
VI – 20min
VII – 30min
3
2
1
5s
30s
1min
5min
10min
20min
30min
I
II
III
IV
V
VI
VII
This setting determines the time period the lamp will remain at 100% upon detection.
Note: the timer is reset upon each motion detection.
Hold-time
I – Disable
II – 50Lux
III – 10Lux
IV – 2Lux
2
1
Disable
50Lux
10Lux
2Lux
I
II
III
IV
The daylight threshold can be set on the DIP switches suit to the particular application.
Daylight sensor
5
9
4
11
12
Stand-by dimming level
Detection range
ON/
OFF
Auto Mode
Reset
Power
80%
Test
2s
10%
20%
30s
1min
100%
30min
10min
5min
0s
10s
1min
30%
SC1
SC2
SC3
Scene mode
10min
50%
10%
30min
Hold-time
Stand-by period
5min
Lux
Disable
2Lux
10Lux
50Lux
Daylight Sensor
SC4
Power
100%
+
-
Dim
M/A
3
1
2
7
8
6
10
13
14
15
HRC-05
Note: the buzzer beeps one time when RC receives signal successfully
Permanent ON/OFF [ ]
1. Press button , to select permanent ON or permanent OFF mode.
2. Press button to resume automatic operation. (Please refer to explanation below)
3. The mode will change to AUTO Mode after power failure.
1
2 3 4
button
1
Auto Mode [ ]
2
button
2
Press button to in initiate automatic mode. The sensor starts working and all settings remain as
before the light was switched ON/OFF.
RESET [ ]
Press button , all settings go back to the value of DIP switch settings.
3
button
3
Test 2s function [ ]
1.Press button ,the sensor goes into testmode (hold time2s). N.B. the stand-by period and daylight
sensor settings are disabled in test mode.
8
2.Press button to exit from this mode, and the sensor settings are changed accordingly.
3 4 11
button
8
10
Ambient daylight threshold [ ]
Press button , the latest surrounding lux value overwrites previous lux value learned, and is set as the
daylight threshold. This feature enables the fixture to function well in any environment.
button
10
Power output [ ]
Press button , the output shifts between 80% and 100%, for energy saving purposes.
5
button
5
Dim +/- [ ]
Press button to adjust the light brightness between 10%~100% during hold-time.“+” increases the
light level, “-” will decrease the light level.
9
button
9
Lux disable [ ]
Press button , the built-in daylight sensor is disabled, the light will always operate upon detection
regardless of ambient light level.
14
button
14
Note: this button is disabled.
M/A [ ]
button
15
Detection range [ ]
Press buttons in zone to set detection range at 100% / 50% / 10%.
6
zone
6
Hold time [ ]
Press buttons in zone to set hold time at 30s / 1min / 5min / 10min / 30min.
11
zone
11
Stand-by period [ ]
Press buttons in zone to set the stand-by period at 0s / 10s / 1min / 10min / 30min / +∞.
Note: “0s” means on/off control; “+∞” means bi-leve of dimming control, the light will never switch off.
(i.e. the light remains at the stand-by dimming level until motion is detected.)
12
zone
12
Stand-by dimming level [ ]
Press buttons in zone to set the stand-by dimming level at 10% / 20% / 30% .
7
zone
7
Daylight sensor [ ]
Press buttons in zone to set daylight sensor at 2lux / 10lux / 50lux.
13
zone
13
Scene mode options [ ]
zone
4
There are 4 scene modes built into the remote control for different applications:
SC1 100% 1min 10min 10%
SC2 100% 5min 10min 10%
SC3 100% 10min 30min 10%
SC4 100% 10min +∞ 10%
Scene
options
Detection
range
Hold
time
Stand-by
period
Stand-by
dimming leve
Daylight
sensor
2Lux
2Lux
10Lux
50Lux
Note: the end-user can fine tune the settings by pressing buttons of detection range / hold time /
stand-by period / stand-by dimming level /daylight sensor , the last setting will over-write
that feature of the pre-set scene.
6
11
13
12
7
