background image

 

7

from low power to high power.   

VOX 

Compandor  

Scrambler 

Channel Lock 

One beep sounds when the feature is enabled.   

Two beeps sound when the feature is disabled.   

Battery Latch 

Used to secure or remove the battery.   

Audio Accessory Jack   

Used to connect audio accessories.   

Mini USB Port   

Used to connect accessories such as programming cable, cloning cable and switching 

power.  

 

Battery Information 

Initial Use

 

New batteries from the factory are not fully charged, so be sure to charge a new battery 

for at least 5 hours before initial use. Three full charge-discharge cycles would optimize 

the capacity and performance of your battery. When battery power runs low, it is time to 

recharge or to replace the battery.   

Applicable Battery Packs 

Please only use the battery specified by HYT. Other batteries may burst, causing bodily 

injury and property damage.   

Caution:  

1.  Do not dispose of the battery in fire! 

2.  Recycling and disposal of the battery shall comply with your local regulations.   

3.  Never attempt to dismantle the battery.   

 

Note:  

1.  Charge the battery at a temperature among 5

-40

. Violation of the said limit may 

cause battery leakage or even damage. 

Summary of Contents for HYT TC-310






























Reviews: