manualshive.com logo in svg

HYT TC-300, Owner'S Manual

Share
Download
HYT TC-300 Owner'S Manual Download Page 30

 

28

programmed. 

 

3.

 

VOX earpiece is necessary. 

 

4.

  You dealer may set VOX sensitivity or disable the VOX feature through the 

programming software. The 

VOX

 key is null when the VOX feature is disabled. 

 

Note: 

 

1.

 

If you select the PTT/VOX switch on the earpiece to PTT, you are able to transmit by 

press of the external PTT, no matter whether the VOX feature is enabled. 

 

2.

 

If you select the PTT/VOX switch on the earpiece to PTT, you are disallowed to push 

the switch from PTT to VOX, this action shall cause the radio to continuously 

transmit.

 

3.

  You can select VOX sensitivity according to the surrounding noise level. Activating 

the VOX feature in high noise environment shall cause the radio to continuously 

transmit. 

 

4.

  When continuous transmission occurs, push the PTT/VOX switch from VOX to PTT, 

or turn on the radio again to restore the radio to operational use.

 

 

Note: to order accessories, please contact your dealer. 

 

 

 

Troubleshooting 

 

Symptom

 

Solution

 

Cannot power on the radio.

 

 

The battery has run out. Please recharge 

the battery or replace it with a new one.

 

  The battery is not properly installed. 

Please remove the battery and attach it 

again.

 

The operating time is noticeably 

shorter than normal, even though 

the battery is properly charged.

 

 

The battery has worn out, and it is time to 

buy a new battery.

 

  The battery is not fully charged. Make 

sure that you remove the battery from 

Summary of Contents for TC-300



































Reviews:

No comments

Brands by name

Popular brands

Load more brands