manualshive.com logo in svg

HYT TC-300, Owner'S Manual

Share
Download
HYT TC-300 Owner'S Manual Download Page 25

 

23

 Squelch 

Off

 

 Squelch 

Off 

Momentary 

 

 

Battery Strength Indicator

 

 Channel 

Lock

 

Note See Glossary for definitions of 

Momentary

, 

Monitor and Scan. 

 

 

 

Advanced Operations 

The following functions are programmable by your dealer. 

 

CTCSS/CDCSS 

Set up talkgroups with unique CDCSS/CTCSS to prevent unwanted conversations on the 

same frequency. If CTCSS/CDCSS is set on the current channel, CTCSS/CDCSS match 

is required for the radio to unmute to an incoming signal. If CTCSS/CCSS is not set, the 

radio can receive calls from all users operating on the same frequency. Your dealer may 

set CTCSS/CDCSS for some channels. 

 

This feature does not mean that your conversation will not be heard by others. Radios that 

set with the same CTCSS/CDCSS, or no CTCSS/CDCSS, can receive from you. 

 

Note: See Glossary for definitions of CTCSS and CDCSS. 

 

Battery Save 

The Battery Save feature is automatically activated once no activity on the channel and no 

operation performed (no key press and no knob selection), for extended operation time. 

 

Once the radio detects no activity on the channel and no operation performed (no key 

press and no knob selection) during radio standby time, it shall automatically enter sleep 

mode ten seconds later. Pressing any key or receiving a signal will restore the radio to 

normal operation and exit from Battery Save. 

 

Note: See Glossary for the definitions of Battery Save and Standby.

 

Summary of Contents for TC-300



































Reviews:

No comments

Brands by name

Popular brands

Load more brands