manualshive.com logo in svg

Hyster H50CT, Service & Repair Manual

Share
Download
Hyster H50CT Service & Repair Manual Download Page 25

TRANSMISSION PRESSURE SENSORS

(TRANSDUCERS)

Remove

1. 

Raise the hood. Disconnect the battery.

NOTE:  

Tag electrical connector prior to disconnect

to aid in correct reconnect.

2. 

Disconnect  transmission  wire  harness  from
transmission pressure sensor connectors.

3. 

Remove  transmission  pressure  sensors  from
transmission. See Figure 21.

1. TRANSMISSION PRESSURE SENSORS

(TRANSDUCERS)

2. TRANSMISSION OIL DIPSTICK

3. TRANSMISSION BREATHER

4. TRANSMISSION OIL FILTER

Figure 21. Transmission Pressure Sensors

(Transducers), Replace

Install

1. 

Install new transmission pressure sensors onto
transmission. See Figure 21.

2. 

Connect  transmission  pressure  sensor  connec-
tor to transmission wire harness as tagged dur-
ing removal.

3. 

Connect the battery and close the hood.

TRANSMISSION TEMPERATURE

SENSOR

Remove

1. 

Raise the hood. Disconnect the battery.

2. 

Put the lift truck on blocks. See the Operating
Manual  or  section  Periodic  Maintenance
8000SRM1774 for procedures.

  WARNING 

At  operating  temperature,  the  transmission  oil  is
HOT. DO NOT permit the hot oil to touch the skin
and  cause  a  burn.  Make  sure  oil  is  cool  before
draining.

  CAUTION

Disposal of lubricants and fluids must meet local
environmental regulations.

3. 

Drain  transmission  oil.  See  section  Periodic
Maintenance 8000SRM1774 for procedures.

NOTE:  

Tag electrical connector prior to disconnect

to aid in correct reconnect.

4. 

Disconnect  transmission  harness  from  trans-
mission temperature sensor connector.

5. 

Remove  transmission  temperature sensor from
transmission. See Figure 22.

2200 SRM 1771

Sensors and Switches

19

Summary of Contents for H50CT


























Reviews:

No comments

Brands by name

Popular brands

Load more brands