background image

A.

HIGH MOUNT PRECLEANER FOR CABS WITH-
OUT AIRCO

B.

HIGH MOUNT PRECLEANER FOR CABS WITH
AIRCO

1.

PRECLEANER

2.

PRECLEANER CLAMP

3.

AIR DUCT

4.

U-CLAMP

5.

SUPPORT BRACKET

6.

AIR DUCT CLAMP

Figure 4. Air Filter Assembly with High Mount

Precleaner (Tier 4F/Stage IV)

EXHAUST SYSTEM (TIER 3/STAGE IIIA)

Remove

  WARNING 

Exhaust system must be at room temperature be-
fore starting disassembly or personal injury may
occur.

1. 

Open left- and right-hand hood doors. See Hood
Assembly.

2. 

Remove V-band clamp from turbocharger See
Figure 5.

3. 

Remove V-band clamp from the muffler.

4. 

Remove the exhaust pipe assembly.

1.

MUFFLER

2.

CAP SCREW AND WASHER

3.

CLAMP

4.

EXHAUST PIPE ASSEMBLY

5.

V-BAND CLAMP

Figure 5. Exhaust System (Tier 3/Stage IIIA)

5. 

Place a cap on the air inlet of the turbocharger
to avoid dirt entering the turbocharger.

6. 

Remove the hardware that retains the muffler
to the center hood and remove the muffler.

Install

1. 

Place the muffler on the center hood and attach
the hardware.

2. 

Remove the cap from the air inlet of the turbo-
charger.

3. 

Install the exhaust pipe assembly.

4. 

Tighten the band clamp on the muffler to 54 -
81 N•m (40 - 60 lbf ft).

5. 

Tighten the band clamp on the turbocharger to
5.6 N•m (4 lbf ft).

6. 

Close the hood doors.

0100 SRM 1978

Remove and Install

5

Summary of Contents for B238
















Reviews: