background image

SAFETY PRECAUTIONS

MAINTENANCE AND REPAIR

• When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened, and

that the load being lifted is balanced. Make sure the crane, cables, and chains have the capacity
to support the weight of the load.

• Do not lift heavy parts by hand, use a lifting mechanism.

• Wear safety glasses.

• DISCONNECT THE BATTERY CONNECTOR before doing any maintenance or repair on electric

lift trucks. Disconnect the battery ground cable on internal combustion lift trucks.

• Always use correct blocks to prevent the unit from rolling or falling. See HOW TO PUT THE LIFT

TRUCK ON BLOCKS in the Operating Manual or the Periodic Maintenance section.

• Keep the unit clean and the working area clean and orderly.

• Use the correct tools for the job.

• Keep the tools clean and in good condition.

• Always use HYSTER APPROVED parts when making repairs. Replacement parts must meet

or exceed the specifications of the original equipment manufacturer.

• Make sure all nuts, bolts, snap rings, and other fastening devices are removed before using force

to remove parts.

• Always fasten a DO NOT OPERATE tag to the controls of the unit when making repairs, or if the

unit needs repairs.

• Be sure to follow the WARNING and CAUTION notes in the instructions.

• Gasoline, Liquid Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Diesel fuel are

flammable. Be sure to follow the necessary safety precautions when handling these fuels and
when working on these fuel systems.

• Batteries generate flammable gas when they are being charged. Keep fire and sparks away from

the area. Make sure the area is well ventilated.

NOTE:

The following symbols and words indicate safety information in this

manual:

WARNING

Indicates a hazardous situation which, if not avoided, could result in
death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury and property damage.

On the lift truck, the WARNING symbol and word are on orange back-
ground. The CAUTION symbol and word are on yellow background.

Summary of Contents for 2240 SRM 1























Reviews: