Hyperion EOS0720iNET Charger -
User’s Manual
Visit http://media.hyperion.hk/dn/eos for the newest manuals, firmware, and software
Warnings:
The EOS 0720iNET is a carefully-designed charger with many
built-in safety features, such as reverse polarity protection,
input voltage error warning, and cell-count mismatch
warnings for lithium chemistry batteries. HOWEVER, IT IS
THE RESPONSIBILITY OF THE USER TO INSURE THAT THE
CHARGER IS CONFIGURED AND USED IN A SAFE MANNER
AND IN A PROPER ENVIRONMENT.
•
Always be sure that the charger is properly
configured for the correct battery type.
•
Be sure that your lithium battery pack balance
connector matches the multi-adapter type connected
to the charger.
•
Be sure that the batteries you charge are capable of
charging at the rate you select.
•
Never charge batteries unattended.
•
Charge only in a fire-resistant environment, non-
flammable surfaces such as on concrete or brick.
•
Do not charge near easily flammable materials.
•
Do not charge batteries inside a model.
•
Charging outdoors is recommended whenever
practical.
•
Use only high-quality gold 4mm bullet connectors for
charge output cable connection to the charger. See
“setup”.
•
Properly insulate and regularly inspect all connectors
to eliminate the possibility of short circuit. Damage
caused by output short circuit is not covered by
warranty.
•
Never allow the charger case to contact an AC/DC
power supply case while powered.
•
Do not drop or cause other shock to the charger, nor
subject it to moisture, condensation or liquids.
•
Do not attempt to charge battery packs made from
different types of cells, a mixture of old and new
cells, or cells made with chemistry not supported by
the EOS 0720i NET.
•
NEVER attempt to charge “non-rechargeable” cells
•
Do not open the case of the charger under any
circumstances. Doing so will void the warranty.
•
Keep the charger away from children or pets at all
times.
HIGH RISK CHARGING ADVISORY
Avoid charging batteries indoors. If you must charge indoors – or any place
injury to persons or damage to property could occur in the event of fire –
then be sure to:
* Keep battery well away from flammables (2 meters or more)
* Contain battery in a heavy fireproof container (such as a brick box)
* Always monitor the charge
HYPERION ACCEPTS NO RESPONSIBILITY FOR DAMAGE
OR INJURY DURING INDOOR, NON-MONITORED or other
HIGH RISK CHARGE ACTIVITY
Specifications & Features:
•
250W max CHARGE Output
•
0.1A to
20.0A
max Charge Current in 0.1A steps
(constrained by 250W max)
•
80W/10A max DISCHARGE limits
•
STORE MODE allows fast and simple discharge to 60%
capacity for proper storage of Lithium Battery types =
longer battery life.
•
Charges/Discharges 1 to 7 cells Lithium Polymer Batteries
Per Port
(3.7V/cell nominal types)
•
Charges/Discharges 1 to 7 cells Lithium Ion Batteries Per
Port
(3.6V/cell nominal types)
•
Charges/Discharges 1 to 7 LiFePO4 (A123) cells
(LiFePO4 3.3V/cell nominal, A123 3.3v support)
•
Charges/Discharges/Cycles 1-16 cell NiCd/Ni-MH in three
modes: Normal, Linear, and Automatic
•
Charges/Discharges 1~12 cell Lead Acid Batteries (Pb,
2V/cell)
•
Allows Lithium-Type batteries to 50,000mAh and PB
(lead/acid) batteries to 100Ah capacity
•
Built-in Hyperion LBA10 Balancer with 300mA max balance
rate/cell
•
TCS - Terminal Capacity Selection
•
Rich Data Displays during and after charging and balancing
•
PC Port for Data Logging and Firmware upgrades
•
Temperature Sensor Ports & Temp Stop settings*
•
Wide Voltage Input Range 11v~28v for higher efficiency
when charging high-voltage packs, and compatibility with a
wider selection of AC/DC power supplies
•
Power Supply Amperage Control to allow reliable charging
with lower-output power supplies
•
Power Supply Voltage Control (PS Load Control) works in
concert with Amperage control to insure the charger does
not overload your power supply
•
Input Cable with 4mm Male Conn Clamps
•
Output Cable Set Included, with 4mm Connectors
•
Integral, Thermostat-Controlled Cooling Fans
•
Rugged Aluminum Case with Insulating End Caps
•
2-Line, 16-Character, Yellow Backlit LCD Data Display.
Highly visible in all conditions
•
10 User-definable Memory Positions
•
Firmware upgradable via Win PC **
EOS0720iNET is designed to charge single Lithium-based packs
up to 7S max.
For “flight packs” higher than 7S, Network
two 0720i in SYNC MODE
for charging of two packs to make
a single series-wired flight pack.
(series-wired flight packs from 2x2S=4S to 2x7S=14S are possible)
* Temp sensors available separate: #HP-EOSTMPSEN or EOS1210i-SEN
** Firmware upgrades require USB Adapter #HP-TI-PRGUSB and harness #HP-EOS06-
PCCBL. Firmware upgrades will only become available if and when improvements are
identified in future.
PUT SAFETY AHEAD OF ALL OTHER CONSIDERATIONS!
SEEK MEDICAL ATTENTION IN EVENT OF ANY INJURY!
1
