HygroMatik FlexLine Manual Download Page 47

Page: 47 / 56

Page 47

Certificate:

2125886

Project:

70198540

Master Contract:

238708

Date Issued:

2018-09-28

DQD 507 Rev. 2016-02-18

Page 3

The products listed, including the latest revision described below,

are eligible to be marked in accordance with the referenced Certificate.

Product Certification History

Project

Date

Description

70198540

2018-09-28

Update to report 2125886 to add missing models during project # 70182230-
No charge job

70182230

2018-06-28

Add new series FLH series and SLH series to report 2125886( Contiunation
of partially closed project 70153375)

70027120

2015-03-23

Update report 2125886 to add 230 VAC Control options.

70005960

2014-05-21

Update report 2125886 to add new model HL-27 and revise minor
specifations of non critical components

2387011

2011-01-19

Update Report 2125886 to revise component model numbers and
corrections as per FIR Dt. Aug 19 2010.

2125886

2009-05-21

Steam humidifiers, 3 phase, 60Hz, Models HL06, HL09, HL12, HL18,
HL24, HL30, HL36, HL45 with heater 48A max..

Summary of Contents for FlexLine

























































Search results

Summary of Contents for FlexLine

Reviews:

Related manuals for FlexLine

Brands by name

Popular brands

HygroMatik FlexLine, Manual

Search results

Summary of Contents for FlexLine

Reviews:

Related manuals for FlexLine

Brands by name

Popular brands