5. Lock the tubes together by rotating each adjoining tube in the opposite
direction, ensuring all small tubes are rotated clockwise.
See diagram 5.
6. Secure each tube with just one self-drilling screw in each join.
7. Attach the tube assembly into the axle ends and check for fit. If it doesn’t fit, undo
just one screw in one join and adjust.
8. When the tube length is correct, drill and fasten the remaining screws at each end
of the overlapped tubes. You should have six (6) screws on each tube end where there is a join.
9. Put the tube assembly together with axle crank handle and axle ends by lining up the hole in the end of each tube
with the axle. Push the tube until it meets the plastic surface at each end and secure with plastic bolt and nut
provided.
10.
Attach cords to tubes.
Measure along the tube, 150 mm in from each edge of the pool
toward the middle. There are enough fasteners for up to ten (10) cords to attach the
blanket. These need only be placed 1000 mm apart but we have provided plenty of cord
so you can use ten (10) and they can be cut to a suitable length, up to 1000 mm. You
need to allow at least 400 mm more cord length than the distance between the blanket
and the tube. Mark the tube with cord positions evenly spaced. Fasten a self-drilling
screw through a domed washer at each mark on the flat of the tube to within 3 mm of
being tight. This is enough room to now slide the cord under the washer in a loop and
hold both pieces of cord, then screw until tight.
See diagram 6.
11.
Attach the cord to the blanket.
The cords are fastened to the blanket using the plastic
grommets. For all above ground pools where the tube spans the pool, you will need two
grommets per cord, spaced 50 mm apart.
See diagram 8.
Using a hammer and a piece
of soft timber under the blanket fabric, punch a hole with the wad punch provided at
each grommet location. Push male grommet component through hole. Place female
component into position and tap gently together with a hammer.
Loop the cord through the double grommet and tie it off with a secure knot. Adjust the
length of the cord by loosening the screw on the tube a little, until you can move the
cord and then tighten it when the length is correct.
Variations in the length of the cord will effect how straight the blanket rolls up, so it is
important to adjust the length carefully. If you test roll the blanket onto the tube and
it rolls unevenly, unroll it, adjust the length of the cords and roll it again until the
blanket rolls evenly.
12.
Fitting your overcover.
The reel kit has been supplied with a protective cover to use
when the blanket has been rolled onto the tube. You will void the warranty of most pool blankets if you do not
cover it when stored on a reel. Follow the separate instructions for fitting the grommets and fastening cords to the
overcover. Be sure to cover the blanket every time it is rolled onto the tube.
Warranty
Your advanced reel system is warranted for a full 12 months, and pro rata for up to three years on the plastic
components against faulty workmanship. If you find a component is faulty, post it pre-paid to: Hydrotools P/L,
PO BOX 2037, Crestmead, Qld 4132 with a copy of your proof of purchase. A replacement will be posted to you.
Frequently asked questions
The tube has a small dent in it, will this effect the performance of the reel?
Provided the tube remains straight, the performance will not be effected by a dent or mark on the tube.
Where do I position the reel when I have to fold a section of my blanket?
Position the reel at either the widest end or the opposite end to any section of the blanket that needs to be
folded when stored on the reel. The fold creates an extra thickness on one side that will cause the blanket to roll
unevenly and therefore this should be kept to a minimum.
Twist tubes to
remove
excess play
prior to
screwing
together
Diagram 7
Diagram 5
Diagram 8
Diagram 6
Cord and
washer and
screw
on tube
4
AG 200704 20/7/04 1:17 PM Page 4
