background image

LIFETIME LIMITED WARRANTY

Residential Cast Iron Water Boilers

First Through Tenth Year
The “Manufacturer” warrants to the original owner at the original installation site that the cast iron sections of
the Residential Cast Iron Water Boilers (the “Product”) will be free from defects in material or workmanship for
ten (10) years from the date of installation. If upon examination by the Manufacturer the Product is shown to
have a defect in material or workmanship during the warranty period, the Manufacturer will repair or replace,
at its option, that part of the Product which is shown to be defective.

Eleventh Year and Above
The Manufacturer warrants that the cast iron sections of its residential cast iron water boilers will remain free 
of defects in material or workmanship under normal usage for the lifetime of the original owner at the original
installation site. Should any sections be found to be defective, the Manufacturer will repair or replace, at its
option, the original cast iron sections upon the payment of a proportionate charge based on the time the
defective section was in service. The proportionate charge will be equal to the appropriate percentage of the
trade price of the section at the time the warranty claim is made, determined as follows:

Year  11

12

13

14

15

16

17

18

19 20 21 22

23 24 25 

Above

% of
Trade

5

10

15

20

25

30

35

40

45

50

55

60

65

70

75

Price

This limited warranty does not apply:
(a) if the Product has been subjected to misuse or neglect, has been accidentally or intentionally damaged, 

has not been installed, maintained or operated in accordance with the furnished written instructions, or has
been altered or modified in any way.

(b) to any expenses, including labor or material, incurred during removal or reinstallation of the Product or 

parts thereof.

(c)  to any other cast iron parts of the boiler.
(d) to burners, jackets, controls, and other auxiliary equipment furnished by the Manufacturer, but

manufactured by others. Any warranties for such items shall be limited to those warranties offered by the
original equipment manufacturer.

(e)  to damage as a result of settlement, distortion, collapse, or cracking of any foundation area, beams or 

pipes surrounding the Product.

(f)  to any workmanship of any installer of the Product; or to Products installed outside the continental United

States or Canada.

This limited warranty is conditional upon:
(a) shipment, to the Manufacturer, of that part of the Product thought to be defective. Goods can only be

returned with prior written approval from the Manufacturer. All returns must be freight prepaid.

(b) determination, in the reasonable opinion of the Manufacturer, that there exists a defect in material or

workmanship

(c)  the residential water boiler having been installed in a single–family or two–family residential dwelling.

Repair or replacement of any part under this Limited Warranty shall not extend the duration of the warranty
with respect to such repaired or replaced part beyond the stated warranty period.

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED,
AND ALL SUCH OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES 
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE  HEREBY DISCLAIMED 
AND EXCLUDED FROM THIS LIMITED WARRANTY. IN NO EVENT SHALL THE MANUFACTURER BE 
LIABLE IN ANY WAY FOR ANY CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES  OF ANY
NATURE  WHATSOEVER, OR FOR ANY AMOUNTS IN EXCESS OF THE SELLING PRICE OF THE
PRODUCT OR ANY PARTS THEREOF FOUND TO BE DEFECTIVE. THIS LIMITED WARRANTY GIVES 
THE ORIGINAL OWNER OF THE PRODUCT SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS WHICH MAY VARY BY EACH JURISDICTION.

IN CANADA: 

7555 TRANMERE DRIVE  

MISSISSAUGA, ONT. L5S 1L4 

TEL (905) 670-5888  
FAX (905) 670-5782

IN UNITED STATES: 

260 NORTH ELM ST.  

WESTFIELD, MA 01085  

TEL (413) 564-5515  
FAX (413) 568-9613

www.hydrotherm.com

Summary of Contents for HVX 175









































Reviews: