HYDROCOWL SAFE-T-COVER 600TD Series Assembly Instructions Download Page 1

 

 

 

The information contained herein is intended for the use of the individual(s) named above and those authorized to receive it.  Dissemination, distribution 
or copy of this information is strictly prohibited.

 

ASSEMBLY INSTRUCTIONS PLEASE READ CAREFULLY 

 

Model No.

 

Inside

 

Dimensions

 

Outside

 

Dimensions

 

Recommended Concrete

 

Pad Dimensions

 

600TD Series 

70"W x 108"L x 64"H 

73 3/4"W x 111"L x 67 1/4"H 

84"W x 122"L x 6" Thick 

1.

 

The concrete base should be 6” thick x 14” longer than enclosure ID x 14” wider than enclosure ID. 

A.

 

Mark the concrete base for the outside of the enclosure (3” wider than ID and 3” longer than ID). 

2.

 

The PVC masking film will  help to protect the  finish of the metal panels during installation.  These 
coatings should be left intact and removed only after assembly of the enclosure is complete. 

A.

 

Stand both  sets  of “A1” & “A2” panels  firmly together.  Fasten the panels together through the holes 
provided on the inside of the panels using hex headed screws.  Make sure the panels are pulled tightly 
together  before  tightening  the  screws.    (For  best  results,  insert  a  bead  of  silicone  caulk  into  the  inside 
bend of the “A1” panel flanges.)  

B.

 

Assemble  each  “B-A1-A2-B”  (side-end-side)  assembly  through  the  holes  provided  using  hex  headed 
screws.  Set them on the marked concrete base (Fig. 2).  (For best results, insert a bead of silicone caulk 
into the inside bend of the “A#” panel corners.) 

Summary of Contents for SAFE-T-COVER 600TD Series

Page 1: ... ID and 3 longer than ID 2 The PVC masking film will help to protect the finish of the metal panels during installation These coatings should be left intact and removed only after assembly of the enclosure is complete A Stand both sets of A1 A2 panels firmly together Fasten the panels together through the holes provided on the inside of the panels using hex headed screws Make sure the panels are p...

Page 2: ... adjacent panels prior to attaching any bracket to the concrete 4 Set the C access panels in place with about a 3 16 gap on each side of the C panels as the roof is assembled A Set the D1 roof panel on a B A1 A2 B side end side assembly Fasten the D1 roof panel to the B A1 A2 B side end side assembly through the holes provided Fig 1 using three 3 hex headed screws B Insert an Inside Roof Clip into...

Page 3: ...e B panels and concrete along one side of the enclosure B Insert Inside Roof Clips into the D roof panels at the B side panel studs Fig 1C Attach the clips to the B panels using one 1 hex headed screw per clip Fasten Inside Roof Clips to the B and D panels along one side of the enclosure C Repeat Steps 6 6A and 6B on the other side and end of the enclosure 7 Install Roof Cover Plates on the D1 D2 ...

Page 4: ...ld include A 2 A1 end Panels B 2 A2 end Panels C 4 B side Panels D 1 C removable access Panel E 1 Cw d removable access Panel F 1 D1 roof Panel G 1 D2 roof Panel H 4 Outside Corner Anchoring Brackets 1 x 1 I 6 Inside Anchoring Brackets 3 x 3 J 6 Inside Roof Clips K 2 Roof Cover Plates L 1 Inner Roof Connection Bracket M 1 Package of Anchors N 1 Package of Hex headed screws O 1 Masonry Bit P 1 Magn...

Reviews: