Hydro Instruments VPH-10000-2 Series Instruction And Operation Manual Download

Page: 29 / 33

FIgurE 6b: Vaporizer Parts List

Item No. Hydro Part Number

Description

Qty.

VPH-10000-PT-300

pressure transmitter

VPH-10000-PT-300A

pressure transmitter

VPH-10000-TC-K-GAS

Gas temperature thermocouple, Type K

VPH-10000-TC-TW

thermowell

VPH-10000-TC-TWA

thermowell

VPH-10000-3

Pressure chamber top flange

VPH-10000-FB-1

Pressure chamber flange bolts

VPH-10000-FN-1

Pressure chamber flange nuts

VPH-10000-MRA

Magnesium anode adaptor

VPH-10000-2-MAG-SET

Set of four (4) magnesium anodes

VPH-10000-000-2

Chlorine pressure chamber (complete assembly)

VPH-10000-FB2

Water tank flange bolts

VPH-10000-FN2

Water tank flange nuts

VPH-10000-002

Water bath flange gasket

VPH-10000-LE

Lifting eyebolts

VPH-10000-001

Pressure chamber flange gasket

VPH-10000-003

Level sensor mounting assembly

VPH-10000-LP

Water level sensor

VPH-10000-PP

3" View port cap

VPH-10000-2-H-240

Heater, 18kW, 240VAC, 3PH

VPH-10000-2-H-380

Heater, 18kW, 380VAC, 3PH

VPH-10000-2-H-480

Heater, 18kW, 480VAC, 3PH

VPH-10000-MB-2

Floor plate mounting bracket

VPH-10000-WS-120

Water Refill Solenoid (120 VAC)

VPH-10000-WS-240

Water Refill Solenoid (240 VAC)

VPH-10000-Corp-1.5

Stainless steel drain valve

VPH-10000-000-1

Water Tank (no piping/fittings)

VPH-10000-CSP-1

Vaporizer inlet pipe

AH-1642

Vaporizer inlet/outlet union

VPH-10000-CSP-2

Vaporizer outlet pipe

VPH-10000-2-TC-K-H2O

Water Tank Thermocouple (Type K)

Summary of Contents for VPH-10000-2 Series


































Search results

Summary of Contents for VPH-10000-2 Series

Reviews:

Related manuals for VPH-10000-2 Series

Brands by name

Popular brands

Hydro Instruments VPH-10000-2 Series, Instruction And Operation Manual

Search results

Summary of Contents for VPH-10000-2 Series

Reviews:

Related manuals for VPH-10000-2 Series

Brands by name

Popular brands