manualshive.com logo in svg

HydraMaster Diamond Products GTXR+, Owner'S Manual And Maintenance Logs

Share
Download
HydraMaster Diamond Products GTXR+ Owner'S Manual And Maintenance Logs Download Page 10

  Diamond Products GTXR+ - Owner’s Guide:  8

Installation Responsibilities

•  Ensure proper payload capacity. It is the distributor’s responsibility to verify that the 

equipment package does not exceed the vehicle capacity.

• 

Ensure installation of a safe fuel tap system and through-floor fittings as provided by 

HydraMaster.

•  Proper placement of the truckmount, recovery tank, fresh water tank, and accessories 

in the vehicle and securing them with bolts and back up plates. The distributor should 
verify that the owner is in agreement with the layout.

•  Ensure proper connection of the fuel lines.
•  Ensure proper connection and installation of the battery. Verify that the battery is in 

accordance with HydraMaster’s recommendation.

•  Check the pump, vacuum blower and engine oil levels prior to starting the truckmount.
•  Start and run the truckmount and check that all systems function properly.
•  Test all hoses, wands, etc. for correct operation.
•  Ensure timely return of the document package.

Summary of Contents for Diamond Products GTXR+


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands