Hydac OF5 CM Operating And Maintenance Instructions Manual Download Page 67

Page: 67 / 80

HYDAC FILTER SYSTEMS GMBH

Appendix | 9

BeWa OF5 CM 3580053c en-us print

67 / 80

9 Appendix

In this annex, you will find supplementary information on the
product.

9.1 EC declaration of conformity

The EC declaration of conformity can be found in the technical
documentation that is part of the scope of delivery for the prod-
uct.

9.2 Locating spare parts

Use only original spare parts for a long and defect-free life cy-
cle of the product. When ordering spare parts and accessories
make sure to always indicate the exact model code and the se-
rial number.

Description

Part no.

Motor pump assembly
230 V / 50 Hz, 1 Ph, 0.75 kW

P3M

3041675

Motor pump assembly
400 V / 50 Hz, 3 Ph, 1.5 kW

P6N

3038709

Vane pump

NBR 721206

Vane pump

NBR 721207

Vane pump

FPM 721317

Vane pump

FKM 721281

Clogging indicator, green/red

36198

Clogging indicator, 0 … 16 bar

39173

Tab. 7: Spare parts list OF5…

*) available on request

Description

Part no.

Pressure hose with lance, length =
3 m

NW25

381465

Pressure hose with lance, length =
5 m

NW25

349004

Summary of Contents for OF5 CM

















































































Search results

Summary of Contents for OF5 CM

Reviews:

Related manuals for OF5 CM

Brands by name

Popular brands

Hydac OF5 CM, Operating And Maintenance Instructions Manual

Search results

Summary of Contents for OF5 CM

Reviews:

Related manuals for OF5 CM

Brands by name

Popular brands