manualshive.com logo in svg

HYDAC International ALPC 9000 Series, Operating And Maintenance Instructions Manual

Share
Download
HYDAC International ALPC 9000 Series Operating And Maintenance Instructions Manual Download Page 55

ALPC 9000 series 

Performing Maintenance

 

Change the sealing disk on the vacuum hand 

To change the sealing disk on the vacuum hand, proceed as follows: 

 

1. 

Screw out the screw (A) using a wrench (wrench opening 10) out clockwise. 

2 

Remove the lock washer and washer (B). 

3. 

Pull the lower, old sealing disk (C) carefully off the vacuum hand and 
dispose of it in an environmentally friendly manner. 

4. 

Clean the sealing surface on the vacuum hand. 

5. 

Put the screw (A) including the lock washer and washer (B) through the hole 
in the new sealing disk (C). 

6. 

Screw in this package with the screw manually in counterclockwise direction 
into the underside of the vacuum hand and tighten the screw slightly with a 
wrench (wrench opening 10) 

7. 

The procedure for changing the sealing disk (C) is completed. 

 

HYDAC FILTER SYSTEMS GMBH 

en 

Page 55 / 68

BEWA ALPC9000 3601005 en 2011-04-07.doc 

2011-04-06

 

Summary of Contents for ALPC 9000 Series





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands