HYCON HPP27VMF Operating Manual Download Page 5

 

Starting Instructions

 

 

Please observe the starting instructions on the front of the powerpack. 
 
Start: 

  Check engine oil level 

 

Check hydraulic oil level at sight glass 

 

Connect hoses and tool 

 

Switch fuel tap to “ON”  

 

Activate choke 

 

Turn ignition key 

 

Activate electric start or pull recoil starter 

 

Set the flow – see below 

 
Stop: 

  Move all levers to “OFF“  

 

Turn off the ignition switch  

 

Turn the fuel tap to “OFF” 

 

 

Setting of Flow 

 

The powerpack has three connections, allowing for connection of two tools 
simultaneously. The connections are marked A, B and C, respectively. 

  
The oil flow can be adjusted by regulating the engine r.p.m. by means of the 
throttle. Connection A can be set to 30-60 l.p.m. / 8-16 g.p.m. Connections B and C 

can be set to 20-30 l.p.m. / 4-8 g.p.m. Connection A cannot be used simultaneously 
with connections B and C. 
  
Each connection is equipped with an ON-OFF lever. Connections not in use must be 

set at OFF, and connections in use must be set at ON. Connections B and C can only 
be used when connection A is OFF. Never turn the lever to ON if no tool is 
connected.  

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for HPP27VMF








Reviews: