manualshive.com logo in svg

HWH 625 Series, Operator'S Manual

Share
Download
HWH 625 Series Operator'S Manual Download Page 3

MP25.3043

12JUN03

DUMP

LEVEL

HWH COMPUTERIZED LEVELING

UNDERSTAND OPERATOR’S MANUAL BEFORE USING.  BLOCK FRAME AND TIRES

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

EXCESS

SLOPE

NOT IN

PARK/

TRAVEL

OFF

CAUTION!

STORE

"EXCESS SLOPE"
LIGHT

"NOT IN PARK" LIGHT

ON LIGHT

"STORE" BUTTON

"DUMP" BUTTON

"OFF" BUTTON

"TRAVEL MODE" LIGHT

FRONT RETRACT BUTTON

FRONT EXTEND BUTTON

WARNING LIGHTS
(4- Red)

RIGHT SIDE EXTEND BUTTON

RIGHT SIDE RETRACT BUTTON

LEVELING LIGHTS
(4- Yellow)

REAR EXTEND BUTTON

REAR RETRACT BUTTON

STORE LIGHT

LEFT SIDE EXTEND

BUTTON

LEFT SIDE RETRACT
BUTTON

"OFF" BUTTON:
operation.

"LEVEL" (HYD) BUTTON:

"STORE" BUTTON:
"STORE" button.  This button is used to automatically retract
the jacks.

"DUMP" BUTTON:
from the vehicle suspension.  

WARNING LIGHTS:

"EXCESS SLOPE" LIGHT:
the leveling system cannot level the vehicle.

"NOT IN PARK/BRAKE" LIGHT:
when the hand/auto brake is not set and the "LEVEL"

"TRAVEL MODE" LIGHT:
when the ignition is on, when the jacks are retracted and 
there are no red WARNING lights on.

MASTER "JACKS DOWN" WARNING LIGHT:
light mounted in the dash separate from the touch panel. 

and the ignition is "ON".

BUZZER:

CONTROL FUNCTIONS

INDICATOR LIGHTS

CONTROL BUTTONS

Push the "OFF" button to stop hydraulic

The  store  indicator  light  is  above the

This is a manual button for dumping air

This indicator will light when 

This indicator will light 

This indicator light will be on 

This is a 

This is a jacks down warning.  It will sound if the

EXTEND BUTTONS (UP ARROWS):

RETRACT BUTTONS (DOWN ARROWS):

LEVELING LIGHTS:

These buttons will 

extend their respective jack pairs to lift the vehicle.

These buttons

will retract their respective jack pairs to lower the vehicle.

The four yellow indicating lights are 

level sensing indicators.   When a yellow light is on, it 
indicates that its side, end, or corner of the vehicle is low.  
No more than two lights should be on at the same time.

This is the on button and 

The four red lights surrounding the 

yellow level indicators are jacks down WARNING lights.  
They are functional only when the ignition is in the "ON" 

extended 1/4 to 1/2 inch.

automatic operation button.  The ON indicator light is above

master "JACKS DOWN" warning light is on. 

CONTROL IDENTIFICATION

625 SERIES LEVELING SYSTEM

COMPUTER-CONTROL

MODE

BRAKE

or "ACC" position, the system is on, and the jacks are

It will be on when any one or more jacks are extended 

HYD

"LEVEL" (HYD) BUTTON

the "HYD" button.

button is being pushed.

Summary of Contents for 625 Series










































Reviews:

No comments

Brands by name

Popular brands

Load more brands