Hutt W77 Product Manual & Warranty Card Download Page 30

How to use the cleaning cloth immediately after 

rinse?

(Overwet cloth is likely to cause a large amount of water being sucked into the 

machine. Please perform this operation with caution)

Pay special attention to cleaning with a full wet cloth, for it leads to slipping of 

the machine and increase the chance of falling. Please ensure no accidental 

injury be caused. If it is bound to be performed, make sure the following steps 

be followed:

① Soak the cloth in clean water, brush off the dirt on the surface and squeeze 

out the excess water. Please be careful to avoid deformation by force while 

removing the water. You may use a hair dryer to dry it as much as possible and 

minimize the moisture in the cloth.

② The cleaning cloth should be fit flat on the base, no gap or deformation.

③ Use dry toilet paper to absorb the moisture at the front and back of the walking 

wheels, to ensure the front and rear areas of the two walking wheels are dry.

④ Try not to wipe frameless glass with a damp cloth.

⑤ When the machine starts to move, it may slide down or stop at the edge. It is 

abnormal walking caused by excessive moisture. Please observe if it can 

gradually return to normal. If not, please use toilet paper again to absorb the 

moisture on the cloth and the caterpillar wheels, thereby helping the machine 

to resume normal operation.

Start up

① Make sure the battery is fully charged and the battery cover is in place.

② Adsorb the sucker on a reasonable position according to actual conditions, 

and ensure it is firmly adsorbed.

③ Turn on the power switch at the bottom, make sure the fan rotates, and 

place the machine far away from the window frame.

④ Make sure the machine has been attached to the glass and let it go.

⑤ Press the start button and the machine will start to move.

Take off the machine

① As the machine is running, hold the safety rope with one hand, hold the 

machine with the other, press and hold the round button so that the suction 

drops, and then take off the machine.

② If you cannot reach the machine and there is no remote control, please pull 

the safety rope along the glass, and slowly pull the machine back to where you 

can reach, and then take off the machine.

③ Turn off the bottom power switch after having retrieved the machine.

④ Pull the round handle on each side of the sucker to take it off.

8

Summary of Contents for W77









































Reviews: