manualshive.com logo in svg

HUSTLER FasTrak SDX, Operator'S Manual, Page: 33 / 41

Share
Download
HUSTLER FasTrak SDX Operator'S Manual Download Page 33

604856

4-7

REV J

Mower Blade Replacement

IMPORTANT:  Refer to the

 Safety 

section of this manual for 

blade handling safety information. 

 

A 15/16" wrench is required to remove the 5/8" cap screw 

holding the blade to the spindle shaft. 

NOTE:

 A blade holding 

tool (part number 381442) is available from Hustler

®

 Turf 

Equipment. It is designed to prevent the blades from rotating 
when they are being removed or installed on the spindle. Con-
tact your Hustler

®

 Dealer for more information.

Do not re-use spindle bolts which have stripped, worn or 

undercut threads. Torque bolts on spindles to 118 ft-lbs 
(160.0 N•m) when reinstalling blades. 

 

Properly compressed cup washers maintain the correct 

compression load on the blades. Replace the cup washers if 
they are cracked or flattened.

IMPORTANT:  

The blade sail (curved part) must be point-

ing upward toward the inside of the deck to ensure proper 
cutting.

When mounting blades, rotate them after installation to 

ensure blade tips do not touch each other or sides of the 
mower. 

Seat Adjustment

The seat on the Hustler

®

 Raptor

®

 SD mower can be 

adjusted forward and rearward by pivoting the seat platform 
up and forward. Then, loosen the four cap screws on the 
underneath side of the seat platform. Position the seat where 
you have the best control of the machine and are the most 
comfortable and then tighten the cap screws. Figure 4-14   

Steering Control Lever Adjustment

The steering control levers can be adjusted for operator 

comfort. 

A.

To pivot the upper control levers forward or rearward, 
loosen the cap screws that attach the upper control 
lever to the lower lever. Then, pivot the upper control 
lever. Tighten the cap screws. Figure 4-15

B.

To lower and raise the control levers, remove the cap 
screws. Slide the upper control lever up or down and 
align the holes in it with the holes in the lower lever. 
Re-install the cap screws and tighten. 

The steering control levers should be adjusted so that they 

align with each other when in the neutral position.  

Mower blades are sharp and can cut. Wrap the 
blade(s) or wear gloves and use extra caution 
when servicing them. 

Failure to correctly torque the bolt may result in 
the loss of the blade which can cause serious 
injury.

WAR

N

ING

WARNING

A.

Cap screws

Figure 4-14

A.

Upper control lever

B.

Cap screws

C.

Lower control lever

Figure 4-15

A

A

A

B

C

Summary of Contents for FasTrak SDX










































Reviews:

No comments