background image

 

SERIAL PLATE

 

The serial plate is located inside the cabinet. It contains the necessary information for the appropriate electric 
installation.  Do not remove the serial plate under any circumstance.   

   
CONTROL OF TEMPERATURE  

 

The cabinet has an electronic control for control of case interior temperature. It is installed in the lower part of 
the cabinet. To locate it remove the grills. This control is programmed from the manufacturer for proper 
freezing temperatures. 
   

DEFROST TIME CLOCK 

The Defrost Time Clock comes programmed from the factory. Defrost is set for every 24 hours for a duration of  
50 minutes.    

   
MAINTENANCE

   

 
Long life and satisfactory performance of any equipment is dependent upon the care it receives.  To ensure long 
life, proper sanitation and minimum maintenance costs, these merchandisers should be thoroughly cleaned, all 
debris removed and the interiors washed down periodically. 
   

Exterior Surfaces 

The exterior surfaces should be cleaned with a mild detergent and warm water to protect and maintain their 
attractive finish.  

NEVER USE ABRASIVE CLEANSERS OR SCOURING PADS.

 

 

Interior Surfaces 

The interior surfaces may be cleaned with most domestic detergents, ammonia based cleaners and sanitizing 
solutions with no harm to the surface. 
 
   

Condenser    

 

 

    

The condenser needs to be cleaned regularly. A dirty condenser restricts the airflow, causing loss in the 
efficiency of the refrigeration system.  (A regular schedule should be established to clean it frequently).   
Prior to cleaning make sure that the case plug is disconnected from the outlet.  
   
1) Use a stiff bristle brush to remove debris.   
2) A vacuum cleaner may also be necessary to assist with removing dust and dirt. 
3) If the cabinet is located in a susceptible area where the condenser is greased, clean the with a solution of 
lukewarm water and detergent. Be careful that the solution doesn't come in contact with wiring or electric 
components.   
4)The thermostat in position TURNED OFF only disconnects the condenser unit. The compressor will be 
energized until the cabinet is disconnected from the electric outlet.   
   
When cleaning the condenser be careful as the fins may have sharp edges.   
   
 
 
 
 
 
 
 
 

Summary of Contents for NIM









Reviews: