49
SERVICIO Y AJUSTES
TO LEVEL MOWER
Ensure tires are properly in
fl
ated to the PSI shown on tires.
If tires are over or under in
fl
ated, it may affect the appear-
ance of your lawn and lead you to think the mower is not
adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 30)
• With all tires properly in
fl
ated and if your lawn appears
unevenly cut, determine which side of mower is cutting
lower.
NOTE:
As desired, you can raise the low side of mower
or lower the high side.
• Go to side of mower you wish to adjust.
• With a 3/4" or adjustable wrench, turn lift link adjustment
nut (A) to the left to lower the mower, or to the right to
raise the mower.
NOTE
: Each full turn of adjustment nut will change mower
height about 3/16" (4,7 mm).
• Test your adjustment by mowing some uncut grass and
visually checking the appearance. Readjust, if neces-
sary, until you are satis
fi
ed with the results.
Fig. 30
Fig. 31
PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 31
• With all tires properly in
fl
ated, park tractor on level
ground or driveway.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
• Raise mower to its highest position.
• At both sides of mower, position blade at side and mea-
sure the distance (A) from bottom edge of blade to the
ground. The distance should be the same on both sides.
• If adjustment is necessary, see steps in Visual Adjust-
ment instructions above.
• Recheck measurements, adjust if necessary until both
sides are equal.
NOTE:
Each full turn of the adjustment nut will change
mower height about 1/8" (3,1 mm).
• Recheck measurements, adjust if necessary until front
tip of blade is 1/8" to 1/2" (3,1 to 12,7 mm) lower than
the rear tip.
• Hold adjustment nut in position with wrench and tighten
jam nut securely against adjustment nut.
B
B
Fig. 32
Fig. 33
FRONT-TO-BACK ADJUSTMENT (See Figs. 32 & 33)
IMPORTANT:
Deck must be level side-to-side.
To obtain the best cutting re sults, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" (3,1 to 12,7 mm)
lower than the rear tip when the mower is in its highest
position.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
• Raise mower to highest position.
• Position any blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear tip
of the blade.
• If front tip of blade is not 1/8" to 1/2" (3,1 to 12,7 mm)
lower than the rear tip, go to the front of tractor.
• With an 11/16" or adjustable wrench, loosen jam nut A
several turns to clear adjustment nut B.
• With a 3/4" or adjustable wrench, turn front link adjust-
ment nut (B) clockwise
( )
(tighten) to raise the front of
mower, or, counterclockwise
( )
(loosen) to lower the
front mower.
TIGHTEN
ADJUST
NUT
B
TO RAISE
MOWER
LOOSEN
ADJUST
NUT
B
TO
LOWER
MOWER
LOOSEN JAM
NUT A FIRST
A
B
TURN NUT LEFT
TO LOWER MOWER
TURN NUT RIGHT
TO RAISE MOWER
A
A
A
Summary of Contents for TS 248G
Page 58: ...58 SERVICE NOTES AVISO ...
Page 59: ...59 SERVICE NOTES AVISO ...
