Husqvarna TC 50 2023 Owner'S Manual Download

Page: 88 / 196

12 BRAKE SYSTEM

12.11

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear

brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

V02857-11

–

Detach the foot brake lever spring.

–

Loosen nut

–

Turn back push rod

until free travel is at a maximum.

–

For an individual adjustment of the basic position of the foot
brake lever, loosen the screw

and turn the eccentric

brake lever stop

accordingly.

–

Tighten screw

Guideline

Remaining screws,

chassis

10 Nm (7.4 lbf ft)

–

Turn push rod

accordingly until you have free travel

Guideline

Free travel of foot brake

lever

3 … 5 mm (0.12 … 0.2 in)

–

Hold push rod

and tighten nut

–

Attach the foot brake lever spring.

–

Check whether the basic position of the foot brake lever is

suitable for the rider.

12.12

Checking the rear brake fluid level

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the specified marking or the specified value, the brake system is

leaking or the brake linings are worn down.

–

Check the brake system and ensure that nobody drives the vehicle before the problem is elimi-

nated. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service

schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands