Husqvarna TC 50 2023 Owner'S Manual Download

Page: 41 / 196

TUNING THE CHASSIS 10

Info

This is due to the volume of the hose and not due to a

defect in the fork airpump or the fork.
Observe the accompanying instructions for Husq-

varna Motorcycles technical accessories.

–

Adjust the air pressure as specified.
Guideline

Air pressure

2 bar (29 psi)

Gradual changing of the air

pressure in steps of

0.2 bar (3 psi)

Minimum air pressure

1.4 bar (20 psi)

Maximum air pressure

4 bar (58 psi)

Info

Never adjust the air pressure to a value outside the

stated range.

–

Disconnect the fork airpump from the left fork leg.

When disconnecting, excess pressure will escape from

the hose

–

the fork leg itself does not lose any air.

The fork airpump indicator switches off automatically

after 80 seconds.

–

Mount the protection cap.

Info

Only mount the protection cap by hand.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 42)

10.14

Adjusting the rebound damping of the fork (TC 50)

Info

The hydraulic rebound damping determines the fork suspension behavior.

F02224-10

–

Turn adjuster

clockwise all the way.

Info

Adjuster

is located at the upper end of the right

fork leg.

–

Turn counterclockwise by the number of clicks correspond-

ing to the fork type.
Guideline

Rebound damping

Comfort

15 clicks

Standard

12 clicks

Sport

10 clicks

Summary of Contents for TC 50 2023





































































































































































































Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands

Husqvarna TC 50 2023, Owner'S Manual

Search results

Summary of Contents for TC 50 2023

Reviews:

Related manuals for TC 50 2023

Brands by name

Popular brands