Husqvarna Soff-Cut 2500 Operator'S Manual Download Page 10

10

FUEL HANDLING

PROPER FUEL

Taking the following precautions will lessen the risk 
of injury and property damage:

- Use extreme care in handling gasoline. It is  

  extremely flammable and the vapors are explosive.

 

- Extinguish all cigarettes, cigars, pipes, and other               
  sources of ignition.
- Use only approved gasoline containers.
- Never remove gas cap or add fuel with the engine     
  running.  Allow engine to cool a minimum of 3 
  minutes before refueling.
- Never fuel the machine indoors.   
- Never store the machine or fuel container where     

  there is an open flame, spark, or pilot light such as   

  on a water heater or other appliances.

- Never fill containers inside a vehicle or on a truck   

  or trailer bed with a plastic liner. Always place  

 

  containers on the ground away from your vehicle    

  when filling.

- Remove the 

2500

 from the truck or trailer and 

  refuel it on the ground. If this is not possible, then     
  refuel the equipment with a portable container,    
  rather than from a gasoline dispenser nozzle.
- Keep the nozzle in contact with the rim of the fuel  
  tank or container opening at all times until fueling is  
  complete. Do not use a nozzle lock-open device.
- If fuel is spilled on clothing, change clothing  
  immediately.

- Never overfill fuel tank. Always wipe off any spilled  

  fuel or oil.  Replace fuel cap and tighten

The Honda engine is certified to operate on automotive un

-

leaded gasoline with a pump octane rating (M+R) of 

87

 or 

higher. Fuel tank capacity is 1.7 gallon (6.5 liter). 

Refuel in a well-ventilated area with the engine 

stopped

You may use regular unleaded gasoline containing no more 
than 10% ethanol (E10). Do not use gasoline containing 
methanol. 

Use of fuels with an ethanol content of more than 10% (E10) 
may cause starting and/or performance problems. It may also 
damage metal, rubber, and plastic parts of the fuel system, as 

well as posing a fire hazard. 

Do not use fuel that is older than 30 days. Old fuel can cause 
running problems as well as fuel system damage.

The engine will not operate on gasoline 
marketed as E-85 (85% ethanol)

OIL HANDLING

WARNING

  

Used oil is a hazardous waste product.  Dispose  

  of used oil properly.  Do not discard with household 
  waste.  Check with your local authorities, service  
  center, or dealer for safe disposal/recycling facility.

NOTICE

ENGINE OIL

Oil Recommendation

The engine holds approximately 1.2 quart (1.1 liter) when 
changing oil.

- Use a 4-stroke automotive detergent oil of API service class  
  SE or higher grade. 
- Do not use special additives.
- Choose a viscosity according to the table below.

Please read the enclosed Honda Operator’s Manual for com-
plete oil information.

HYDROSTATIC TRANS OIL

Mobil DTE 26 

hydraulic oil or equivalent (20W with viscosity 

of 68)

Summary of Contents for Soff-Cut 2500



















Reviews: