Husqvarna SG13 Operator'S Manual Download Page 23 | Manualshive

Page: 23 / 48

background image

CONTROLS

23

Brake

The lever activates a disk brake on the left wheel
when it is pulled backwards. The brake should always
be activated when the grinder is parked, is being
transported or when it is in operation

Handle Adjustment Bar

As the tree stump is ground away, the handle position
will need to be adjusted. Pull the handle backwards
and set the handle at a suitable working height.
Engagement rods are spring loaded to insure positive
locking when released, but always make sure bolts
are locked into place after adjustments are made.

WARNING!

NEVER operate a machine with a
defective brake.

WARNING!

To avoid the risk of losing control
of the machine, DO NOT pull out the
adjustment bar when the cutting
wheel is rotating.

8064-013

8064-014

«
...
21
22
23
24
25
...
»

Summary of Contents for SG13

















































Reviews:

No comments

Related manuals for SG13

Brand: 1st-line Pages: 56

Brand: QUAMAR Pages: 104

Brand: Saturn Pages: 36

Brand: Baratza Pages: 13

HOME HG HD 1300/SZ

Brand: Somogyi Elektronic Pages: 16

Brand: Metabo Pages: 16

Brand: EMGA Pages: 14

Brand: Vulcan Concept Pages: 60

Brand: Heinner Pages: 52

Brand: Constructor Pages: 47

Brand: Flex Pages: 209

Brand: Scheppach Pages: 152

Brand: IKA Pages: 100

Brand: Hercules Pages: 12

Brand: Jet Pages: 20

Brand: Jet Pages: 20

Brand: Jet Pages: 24

Brand: Parkside Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands