Husqvarna LH 700 Page 16 Operator'S Manual Download

Page: 16 / 36

2. Move the joystick to move the product in that

direction:

a) Forward operation (A).
b) Right operation (B).
c) Rearward operation (C).
d) Left operation (D).
The vibration starts when you move the joystick.

3. Release the joystick to stop the movement of the

product and the vibration.

System information on the remote control

display

When the remote control starts, this information shows

on the display:

• Hour meter for engine operation (A).
• Software version for the electronic control unit (ECU)

(B).

• Software version for the receiver (C).
• Software version for the remote control (D).
During operation, these messages can show on the

display:

Event

Information on the display

Pairing operation

"Pairing info"

"Pairing RX-TX..."

Pairing operation comple-

ted

"Pairing info"

"Pairing RX-TX- Link OK"

"Pairing ready!"

"Restart system"

Event

Information on the display

Bluetooth

connected

"Pairing info"

"Pairing RX-TX- Link OK"

Bluetooth

fault

"Pairing info"

"Pairing RX-TX- Link ER-

ROR"

"Pairing failed!"

"Restart system"

Link timeout

Pairing operation failed

"Pairing info"

"Pairing RX-TX..."

"Pairing failed!"

"Restart system"

Pairing operation failed

"Pairing info"

"Pairing RX-TX- Link OK"

"Pairing failed!"

"Restart system"

Symbols on the remote control display

The remote control is connected to the

receiver by radio communication.

The battery charges.

The oil pressure is too low. The engine

stops in 30 seconds.

CA: CAN error. Do a check of the

connection between the receiver and the

electronic control unit (ECU).

The remote control is connected to the

receiver by cable.

1177 - 001 - 02.04.2020

Summary of Contents for LH 700





































Search results

Summary of Contents for LH 700

Reviews:

Related manuals for LH 700

Brands by name

Popular brands

Husqvarna LH 700, Operator'S Manual

Search results

Summary of Contents for LH 700

Reviews:

Related manuals for LH 700

Brands by name

Popular brands