background image

Contents

Introduction..................................................................... 2

Safety..............................................................................5

Operation...................................................................... 10

Maintenance................................................................. 18

Transportation, storage and disposal........................... 23

Technical data.............................................................. 26

Registered trademarks................................................. 30

EC Declaration of Conformity....................................... 31

Introduction

Product overview (LH 700)

15

14

13

12

10

11

8

3

1

18

9

16

2

4

7

6

5

16

17

10

1. Ignition lock
2. Handle
3. Throttle control
4. Handle lock for transportation position
5. Lifting point
6. Safety frame
7. Safety straps
8. Eccentric element
9. Type plate
10. Vibration damping units

Note: There are also 7 vibration damping units

between the handle and the engine plate. Refer to 

To do a check of the vibration damping units on

page 9

.

11. Water separator
12. Hydraulic oil tank
13. Battery
14. Engine oil dipstick
15. Fuel tank
16. Drain plug for engine oil
17. Air filter indicator
18. Operator's manual

2

1177 - 001 - 02.04.2020

Summary of Contents for LH 700





































Reviews:

Related manuals for LH 700