background image

• Make sure that the vibration damping units are

correctly installed.

• Examine the vibration damping units for damages

and wear.

• Replace the vibration damping units if it is

necessary.

Fuel safety

WARNING: Read the warning instructions

that follow before you use the product.

• Fuel is flammable and the fumes are explosive. Be

careful with fuel to prevent injury, fire and explosion.

• Do not breathe in the fuel fumes. The fuel fumes are

poisonous and can cause injury. Make sure that the

airflow is sufficient.

• Do not remove the fuel tank cap or fill the fuel tank

when the engine is on.

• Let the engine become cool before you refuel.
• Do not fill fuel in an indoor area. Not sufficient airflow

can cause injury or death because of asphyxiation or

carbon monoxide.

• Do not smoke near the fuel or the engine.
• Do not put hot objects near the fuel or the engine.
• Do not fill fuel near sparks or flames.
• Before you refuel, open the fuel tank cap slowly and

release the pressure carefully.

• Fuel on your skin can cause injury. If you get fuel on

your skin, use soap and water to remove the fuel.

• If you spill fuel on your clothing, change clothing

immediately.

• Do not fill the fuel tank fully. Heat causes the fuel to

expand. Keep a space at the top of the fuel tank.

• Tighten the fuel tank cap fully. If the fuel tank cap is

not tightened, there is a risk of fire.

• Before you start the product, move the product to a

minimum of 3 m/10 ft from where you refueled.

• Do not start the product if there is fuel or engine oil

on the product. Remove the unwanted fuel and

engine oil and let the product dry before you start the

engine.

• Examine the engine for leaks regularly. If there are

leaks in the fuel system, do not start the engine until

the leaks are repaired.

• Do not use your fingers to examine the engine for

leaks.

• Keep fuel in approved containers only.
• When the product and fuel is in storage, make sure

that fuel and fuel fumes cannot cause damage.

• Drain the fuel in an approved container outdoors and

away from sparks and flames.

Battery safety

WARNING: A damaged battery can cause

an explosion and cause injury. If the battery

has a deformation or is damaged, speak to

an approved Husqvarna service agent.

WARNING: Read the warning instructions

that follow before you use the product.

• Use protective glasses when you are near batteries.
• Do not wear watches, jewelry or other metal objects

near the battery.

• Keep the battery out of reach for children.
• Charge the battery in a space with good airflow.
• Keep flammable materials at a minimum clearance

of 1 m when you charge the battery.

• Discard replaced batteries. See 

Disposal on page

21

.

• Explosive gases can come from the battery. Do not

smoke near the battery. Keep the battery away from

open flames and sparks.

Safety instructions for operation on slopes

WARNING: Read the warning instructions

that follow before you use the product.

• Do not operate the product on a slope that is more

than 20°. Loose ground, vibrations and the operation

speed can cause the product to fall on a slope that is

less than 20°.

• Make sure that the work area is safe. Wet and loose

soil decreases safe operation of the product. Be very

careful on slopes and rough surfaces.

• Make sure that all persons in the work area are

above the product on the slope.

• Operate the product up and down the slope, not from

side to side.

• Do not park the product on a slope. If you must park

the product on a slope, make sure that the product

cannot fall. There is a risk of injury and damage.

Safety instructions for operation near edges

WARNING: Read the warning instructions

that follow before you use the product.

• There is a risk that the product falls when you

operate it near an edge. Always keep a minimum of

⅔ of the product on a surface that is sufficiently

stable to hold the product weight.

• If the product falls, stop the engine before you lift the

product back to a surface that is sufficiently stable.

Refer to 

To lift the product on page 20

.

1224 - 002 - 06.04.2020

9

Summary of Contents for LG 400





























Reviews: