Husqvarna F2303U4 Owner'S Manual Download Page 29

Page: 29 / 169

COMBINATION INSTRUMENT 7

401911-01

–

Wait for 5 seconds.

Combination instrument changes to the next menu item.
The

symbol flashes.

–

Press one of the buttons to select the 24h or 12h display of
the clock.

401912-01

–

Wait for 5 seconds.

Combination instrument changes to the next menu item.
The

symbol flashes.

Resetting the time

–

Press the left button.

The value decreases.

Advancing the time

–

Press the right button.

The value increases.

401913-01

–

Wait for 5 seconds.

Combination instrument changes to the next menu item.
The

symbol flashes.

Shortening the service interval

–

Press the left button.

The value decreases.

Extending the service interval

–

Press the right button.

The value increases.

401914-01

Switching off the service interval display

–

Press and hold the left button.

off

appears in the display.

7.5

Adjusting the kilometers or miles

Info

If the unit is changed, the value

ODO

is retained and converted accordingly.

Condition

The motorcycle is stationary.

Summary of Contents for F2303U4










































































































































































Search results

Summary of Contents for F2303U4

Reviews:

Related manuals for F2303U4

Brands by name

Popular brands

Husqvarna F2303U4, Owner'S Manual

Search results

Summary of Contents for F2303U4

Reviews:

Related manuals for F2303U4

Brands by name

Popular brands