Husqvarna F2303U4 Owner'S Manual Download Page 129

Page: 129 / 169

TUNING THE ENGINE 17

127

F02357-10

Main work

–

Move the handlebar to the straight-ahead position.

–

Push back sleeve

–

Loosen nut

–

Turn adjusting screw

in as far as possible.

–

Loosen nut

–

Push cold start button

all the way to the stop.

–

Turn adjusting screw

so that the cold start button moves

to the basic position when the throttle grip is turned to the
front.

–

Tighten nut

–

Turn adjusting screw

so that there is play in the throttle

cable at the throttle grip.
Guideline

Throttle cable play

3 … 5 mm (0.12 … 0.2 in)

–

Tighten nut

–

Slide on sleeve

–

Check the throttle grip for smooth operation.

Finishing work

–

Check the throttle cable play. (

p. 126)

17.3

Adjusting the characteristic map of the throttle response

Info

On the throttle grip, the characteristic map of the throttle response is changed by changing the guide
plate.
A guide plate with a different characteristic map is supplied.

F02366-10

Main work

–

Push back sleeve

–

Remove screws

and half-shells

–

Detach the throttle cables and take off the grip tube.

Summary of Contents for F2303U4










































































































































































Search results

Summary of Contents for F2303U4

Reviews:

Related manuals for F2303U4

Brands by name

Popular brands

Husqvarna F2303U4, Owner'S Manual

Search results

Summary of Contents for F2303U4

Reviews:

Related manuals for F2303U4

Brands by name

Popular brands