Husqvarna F2275U4 Page 73 Owner'S Manual Download

Page: 73 / 162

SERVICE WORK ON THE CHASSIS 12

12.26

Installing the right side cover

H03701-10

Main work

–

Attach side cover with the holding lugs

from below and

push upward.

–

Engage the side cover in areas

and

Finishing work

–

Mount the seat. (

p. 67)

–

Install the air filter box cover. (

p. 68)

12.27

Removing the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down before performing any work on the vehicle.

Preparatory work

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 66)

–

Remove the right side cover. (

p. 70)

S03561-10

Main work

–

Detach spring

Spring hook (50305017000C1)

–

Remove screws

and take off the main silencer.

Summary of Contents for F2275U4



































































































































































Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands

Husqvarna F2275U4, Owner'S Manual

Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands