Husqvarna F2275U4 Page 68 Owner'S Manual Download

Page: 68 / 162

12 SERVICE WORK ON THE CHASSIS

F02307-10

–

Position the foot brake cylinder.

Push rod

engages in the foot brake cylinder.

The dust boot is correctly positioned.

–

Mount and tighten screws

Guideline

Remaining screws,
chassis

10 Nm (7.4 lbf ft)

F02308-10

–

Position the angle lever and linkage lever.

–

Mount and tighten fitting

Guideline

Nut, linkage lever on
angle lever

M14x1.5

60 Nm (44.3 lbf ft)

Info

Pay attention to flat area

–

Mount and tighten screw

Guideline

Screw, bottom
shock absorber

M10

60 Nm (44.3 lbf ft)

Loctite

2701™

Info

Raise the link fork slightly to be able to mount the
screw more easily.

S03555-11

–

Attach frame protector in area

and position.

–

Mount and tighten screws

with the washers.

Guideline

Screw, frame pro-
tector

3 Nm (2.2 lbf ft)

–

Mount the new cable ties.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 54)

12.18

Removing the seat

Preparatory work

–

Remove the air filter box cover. (

p. 68)

Summary of Contents for F2275U4



































































































































































Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands

Husqvarna F2275U4, Owner'S Manual

Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands