Husqvarna F2275U4 Page 94 Owner'S Manual Download

Page: 94 / 162

13 BRAKE SYSTEM

A00365-10

–

Move the brake reservoir mounted on the handlebar to a hori-
zontal position.

–

Remove screws

–

Take off cover

with membrane

S02124-10

–

Manually press the brake caliper toward the brake disc to
push back the brake pistons. Ensure that brake fluid does
not flow out of the brake fluid reservoir, if necessary extract
excess.

Info

Make sure that you do not press the brake caliper
against the spokes when pushing back the brake pis-
tons.

–

Remove cotter pin

–

Push spring plate

upwards and remove pin

–

Take out the brake linings.

–

Clean the brake caliper and brake caliper bracket.

H02377-10

–

Check that spring plate

in the brake caliper and sliding

plate

in the brake caliper bracket are seated correctly.

S02125-10

–

Insert the new brake linings.

–

Mount pin

Spring plate

engages in the groove on the pin.

Info

Always change the brake linings in pairs.

–

Mount cotter pins

–

Operate the hand brake lever repeatedly until the brake lin-
ings are in contact with the brake disc and there is a pressure
point.

Summary of Contents for F2275U4



































































































































































Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands

Husqvarna F2275U4, Owner'S Manual

Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands