Husqvarna F2275U4 Page 118 Owner'S Manual Download

Page: 118 / 162

15 ELECTRICAL SYSTEM

116

» If the boundary between light and dark does not meet

specifications:

–

Adjust the headlight range. (

p. 116)

15.11

Adjust the headlight range.

Preparatory work

–

Check the headlight setting. (

p. 115)

H03755-10

Main work

–

Loosen screw

–

Adjust the headlight range by pivoting the headlight.
Guideline

The boundary between light and dark must be exactly on
the lower mark for a motorcycle with rider (instructions on
how to apply the mark: Checking the headlight setting).

Info

A change in weight on the vehicle may require a cor-
rection of the headlight range.

–

Tighten screw

15.12

Changing the combination instrument battery

Preparatory work

–

Remove the headlight mask with the headlight. (

p. 112)

H03756-10

Main work

–

Remove screws

with the washers.

–

Pull the combination instrument upward out of the holder.

H03757-10

–

Using a coin, turn protection cap

all the way counter-

clockwise and take it off.

–

Remove combination instrument battery

–

Insert the combination instrument battery with the label fac-
ing outward.

Combination instrument battery (CR 2032) (

p. 144)

–

Check the O-ring of the protection cap for correct seating.

Summary of Contents for F2275U4



































































































































































Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands

Husqvarna F2275U4, Owner'S Manual

Search results

Summary of Contents for F2275U4

Reviews:

Related manuals for F2275U4

Brands by name

Popular brands