Husqvarna F2201V1 Owner'S Manual Download

Page: 68 / 158

11 SERVICE WORK ON THE CHASSIS

11.23

Installing the air filter box cover

V01376-10

(FC 350 EU, FC 350 US)

–

Attach catch

of the air filter box in area

and push

forward.

Info

An air filter box cover with openings for greater
airflow and a more direct response is included.

(FX 350)

–

Attach catch

of the air filter box in area

and push

forward.

V01370-11

–

Engage the air filter box cover in areas

and

11.24

Removing the air filter

Note

Engine damage

Unfiltered intake air has a negative effect on the service life of the engine.

Dust and dirt will enter the engine without an air filter.

–

Only operate the vehicle if it is equipped with an air filter.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance
with the applicable regulations.

Preparatory work

–

Remove the air filter box cover. (

p. 65)

K01080-10

Main work

–

Detach retaining tab

–

Remove air filter with air filter support.

–

Remove air filter from air filter support.

Summary of Contents for F2201V1































































































































































Search results

Summary of Contents for F2201V1

Reviews:

Related manuals for F2201V1

Brands by name

Popular brands

Husqvarna F2201V1, Owner'S Manual

Search results

Summary of Contents for F2201V1

Reviews:

Related manuals for F2201V1

Brands by name

Popular brands